Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Car maintenance
3. Четырехцилиндровыв engines
4. VS engines
5. All engines
6. Systems of cooling, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
14.1. Specifications
14.2. General information
14.3. Blocks disk (forward and back) brakes - replacement
14.4. A brake support - removal, dismantling and installation
14.5. A brake disk - check, removal and installation
14.6. Back drum-type brakes - replacement of blocks
14.7. The wheel cylinder of back drum-type brakes - removal, dismantling and installation
14.8. See hl. 1
14.9. Disks of back brakes - check, removal and installation
14.10. Blocks of the hand brake (on back disk brakes) - removal, installation and adjustment
14.11. The main cylinder of brakes - removal, dismantling and installation
14.12. A regulator of pressure of brakes - removal and installation
14.13. The hydraulic actuator highway - check and replacement
14.14. Pumping of brakes
14.15. The vacuum amplifier of brakes - general information and check
14.16. The vacuum amplifier of brakes - removal and installation
14.17. The hand brake - adjustment
14.18. The lever of the hand brake - removal and installation
14.19. Cables of the hand brake - removal and installation
14.20. The switch of a signal of braking - removal and installation
14.21. Anti-blocking system (ABS) - general information and access to codes.
15. Suspension brackets and steering
16. Body and furnish elements
17. Electric equipment system
 






14-5-disk-tormoza-proverka-snyatie-i-ustanovka.html

14.5. A brake disk - check, removal and installation

Check
1. Release nuts of wheels, lift the car and establish on supports. Remove wheels.
2. Remove a support with the cylinder and take aside.
3. Check a disk condition. At detection of traces of deep development (depth more than 0,38 mm) take a disk and прошлифуйте (photo).
4. Check palpation (especially if when braking vibrations were felt) by means of the strelochny indicator (photo). If palpation on the indicator exceeds norm, remove a disk and прошлифуйте.

Attention!
The disk in general is recommended to be removed periodically and прошлифовывать on it is dependent on indicator indications. At least it can be made by hand a small skin (photo) to reduce a roughness.

5. After polishing the thickness of a disk should not be less maximum permissible (the thickness is cast on a disk, a photo).
Removal
6. Remove a dustproof cover of a nave.
7. Remove шплинт.

3.12 Piston installation in the cylinder 1.  Cylinder 2. Piston 3. Cuff 4. Cover


4.4а Check of palpation of a disk


8. Remove a cap.
9. Unscrew a nut of a nave and remove a washer.
10. Remove the external bearing.
11. Remove a nave assembled with a disk.
12. If the disk is перешлифовываться, get: epiploon.

4.4б disk Polishing by hand


4.5а Place of drawing of limiting thickness of a disk


4.13а Bolts of fastening of a disk to a nave


13. If the disk changes, separate it from a nave for what unscrew bolts, обстучите on nave edge, hook screw-drivers and take a disk (photo). If to separate a disk in such a way it is not possible, grease a joint of a disk and a nave with getting liquid.
Installation
14. Establish a disk on a nave and screw bolts.
15. Evenly and gradually tighten bolts to the full.
16. Other operations are carried out according to GL.11.


«previous page
14.4. A brake support - removal, dismantling and installation
following page»
14.6. Back drum-type brakes - replacement of blocks