|
4-10-zubchatyjj-remen-snyatie-i-ustanovka.html
4.10. A gear belt - removal and installation1. Execute a decompression of fuel system and disconnect the battery from weight.
2. Merge cooling liquid.
3. Establish the piston of the 1st cylinder in VMT of a step of compression.
4. Remove the air filter and covers of heads of cylinders.
5. Release bolts of rollers of yokes.
6. Remove all belts, a casing of the fan and a roller of a natyazhitel of a belt of the conditioner.
7. Remove a pulley-uspokoitel.
8. Disconnect the bottom hose of a radiator from a branch pipe and weaken a collar on other end of a branch pipe.
9. Unscrew a bolt and remove a branch pipe.
10. Unscrew bolts of covers of a gear belt (photo). Bolts should be designated, that at assembly to establish on former places.
11. Be convinced that all labels on 3 asterisks are combined with motionless indexes (in a look рисок on covers of a belt and the case of the pump, a photo). Otherwise tighten the crankshaft before combination of labels, having screwed a bolt of an uspokoitel.
12. Release a nut of a roller (photo).
13. Remove a belt. Check freedom of rotation of a roller (photo).
14. Before installation of a belt turn a natyazhitel clockwise on 70-80 ° and tighten a lock-nut (photo)
15. Establish a belt so that the arrow was turned forward.
16. Combine white risks on a belt with labels on asterisks (photo).
|
|
10.10а Covers of a gear belt
1. The bottom forward cover (on cars 4x2)
2. The bottom forward cover (on cars 4x4)
3. Top forward cover
4. Back cover
|
|
|
10.106 Gear belt and drive details
1. Block of cylinders
2. Adjusting hairpin
3,14. Asterisk
4. Spring
5. Natyazhitel
6,8,13. Washer
7. Leading asterisk
9. Pulley
10,11,15. Cover
12. Conic washer
|
|
Fastening drawing
|
Pozgitsiya number in which
to be rolled; bolt
|
|
1,2,3,4,5 20, 22, 23
|
|
6,24
|
|
7,8,9,10,21 1
|
|
15,16,17.18, 1 11,12,13
|
|
19,25
|
|
|
10.11 Adjusting labels on belt asterisks
1,3,6-labels
2. Back cover
4,9. Left (right) cam-shaft
5. The piston 1 - го the cylinder is in VMT of a step of compression
7. Oil pump
8. Leading asterisk
|
|
|
10.12 Nut of a roller of a natyazhitel of a belt
|
Adjustment
17. Release a lock-nut of a natyazhitel and again turn a natyazhitel on 70-80 ° clockwise (photo).
18. Slowly turn the crankshaft clockwise on 2-3 turns and again expose the piston 1 - го the cylinder in VMT of a step of compression. If big resistance to rotation is felt, return the crankshaft to a starting position and check combination of labels of a belt and pulleys.
19. Holding a natyazhitel, release a lock-nut.
20. Put to a natyazhitel щуп 0,35 mm (photo).
21. Slowly turn the crankshaft while щуп it will not appear between a natyazhitel and a belt (photo).
|
|
10.14 Preliminary adjustment of a natyazhitel
|
|
|
10.16а Combination рисок a belt with labels on asterisks of cam-shafts.
|
|
|
10.16б Before releasing a lock-nut be convinced that the label on a leading asterisk is located opposite risks on the case of the oil pump
|
|
|
10.20 Put щуп in the specified place...
1. Crankshaft
2. Belt
3. Width of 0,500 mm
4. Thickness of 0,35 mm
5. Shchup
6. Appendix place щупа
7. Roller of a natyazhitel
|
|
|
10.25 At check to put effort in the middle between asterisks. The deflection should correspond to the specified
1,2. Cam-shafts
3. Belt
|
|
|
10.17 Natyazhitel of a belt
1. Spring hook
2. A look on an arrow A
3. Hairpin
4. Spring
|
|
|
10.21... also turn the crankshaft while щуп it will not appear between a natyazhitel and a belt
1. Shchup
2. Crankshaft
3. Belt
4. Roller
|
22. Holding a natyazhitel, tighten a lock-nut.
23. Turn the crankshaft and clean щуп.
24. Slowly turn the crankshaft clockwise on 2-3 turns and again expose the piston 1 - го tsilin-the I Wad Dra in VMT of a step of compression.
25. Check a belt tension according to the scheme (photo)
26. Establish all removed details.
|