Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Car maintenance
3. Четырехцилиндровыв engines
4. VS engines
5. All engines
6. Systems of cooling, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
9.1. Specifications.
9.2. General information
9.3. System of compulsory ventilation of a case (PCVсистема)
9.4. System retsirkulyatsiya (EGR system)
9.5. System of a dookisleniye of exhaust gases
9.6. Catching system паров gasoline (EEC system)
9.7. System of electronic injection of fuel self-diagnostics mode
9.8. Regulator of a stream of air
9.9. Regulator of pressure of fuel both solenoidal valve check and replacement
9.10. Sensors of the processor block
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and furnish elements
17. Electric equipment system
 






9-10-datchiki-processornogo-bloka.html

9.10. Sensors of the processor block

Sensor of temperature of the engine
Check
1. The sensor needs check at the complicated start-up of the engine and in case of code 13 detection in a self-diagnostics mode (see above).

9.2 Check of the sensor of temperature of the engine


2. If the engine is not started and there are obvious signs of incomplete combustion of fuel, disconnect the plug and repeat start attempt. If the engine is not started, turn out the sensor and check its resistance depending on temperature (photo). If resistance differs from norm, the sensor replace. Otherwise check a sensor chain.
3. Establish the sensor upside-down.
Check of the sensor of temperature of exhaust gases
4. The sensor needs check in case of code 35 detection in a self-diagnostics mode (see above).
5. If in a mode круизконтроля the engine works unstably, disconnect the socket and check a course of the car (photo).
6. If the course of the car improved, the sensor replace. Otherwise include ignition and check tension on a conclusion of the socket which should be about 5 In (photo).

9.5 The socket of the sensor of temperature of exhaust gases on  V6 engines and К24


9.6 Tension check between a conclusion of the socket of the sensor and weight


9.7 Check of a chain of a conclusion of the socket of the sensor on weight


9.10 The socket of the sensor of oxygen on V6 engines and KS4


9.12 Tension check on a conclusion of the socket of the sensor of oxygen


9.13 Check of a chain of the sensor of oxygen on weight on V6 engines


9.16а the Socket of the sensor of air temperature on K24 engines


7. Switch off ignition and check a chain on weight (photo).
8. If tension differs from 5 In or in a chain there is a break, the sensor replace.
Check of the sensor of oxygen
9. The sensor needs check in case of code 33 detection in a self-diagnostics mode (see above).
10. If in a mode круизконтроля the engine works unstably, disconnect the socket and check a course of the car (photo).
11. If the course of the car improved, the sensor replace. Otherwise finish turns to 2000 rpm and later 2 mines be convinced that on the processor block the green signal blinks.
12. On V6 engines at the included ignition check tension between a conclusion of the socket A and weight which should be about 12 In (photo),
13. Switch off ignition and check a chain on weight (photo).

Attention!
On V6 engines a chain the ohmmeter should show a chain between a conclusion And and weight, and on the K24 engine between a conclusion and and a conclusion of the 19th socket on the processor block.

14. If tension differs from 12 In or in a chain there is a break, the sensor replace.

9.16 tension Check on a conclusion of the socket of the sensor of air temperature


Check and replacement of the sensor of air temperature (on the K24 engine)
15. The sensor needs check in case of code 41 detection in a self-diagnostics mode (see above).
16. Open the socket of the sensor (photo) and at the included
ignition check tension between a conclusion of the socket B and weight which should be about 5 In (photo).
17. If tension corresponds to norm, switch off ignition and check a chain between a conclusion And and weight.
18. Check resistance of the sensor which should be at 20 ° About 2,1 2,9 Ohm, and at 80 ° About 270300 Ohm.
19. In need of replacement turn out the sensor from the air filter and screw the new.

«previous page
9.9. Regulator of pressure of fuel both solenoidal valve check and replacement
following page»
10. Mechanical transmission