Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Car maintenance
3. Четырехцилиндровыв engines
4. VS engines
5. All engines
6. Systems of cooling, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and furnish elements
16.1. Specifications
16.2. Care of loops and locks
16.3. A windscreen and motionless glasses of a body - replacement
16.4. Bumpers - removal and installation
16.5. A forward lattice - removal and installation
16.6. A forward apron - removal and installation
16.7. An air inlet lattice - removal and installation
16.8. A forward wing - removal and installation
16.9. Cowl adjustment
16.10. A cowl - removal and installation
16.11. Cowl locks - removal and installation.
16.12. A cable of a drive of the lock of a cowl - removal and installation
16.13. A back cover - removal and installation
16.14. The lock of a back cover and a drive cable - removal and installation
16.15. The internal panel of a door - removal and installation
16.16. Door glass and a window regulator - removal and installation
16.17. The door lock and handles - removal and installation
16.18. A door - removal and installation
16.19. A window leaf of lateral glass - removal and installation
16.20. Seats - removal and installation
16.21. Seat belts - general information
16.22. The central section - removal and installation
17. Electric equipment system
 








16-15-vnutrennyaya-panel-dveri-snyatie-i-ustanovka.html

16.15. The internal panel of a door - removal and installation

1. Lower glass.
2. Unscrew screws of fastening of an armrest to the panel.
3. Remove the window regulator handle for what the thin bent tool get a spring ring.
For this purpose wring out a decorative slip to get access to a shaft and a spring ring, hook a ring and displace towards the handle, and remove a ring. Remove the handle and a plastic washer.

14.5 For removal of a guard of the handle unscrew one screw
14.5 For removal of a guard of the handle unscrew one screw


4. Remove the handle of the door lock.
5. Take a decorative guard of the handle of a door (photo).
6. Hook a screw-driver and get panel latches from a framework of a door (photo). To get latches begin from below and be displaced up, taking latches on a panel contour. Raise and remove the panel.
7. Before installation check a condition of all for. Lock also be convinced of correctness of orientation of the water filter.
8. Establish the panel, being guided on it is inserted; to a koyatka of a window regulator.

14.6 Latches of fastening of the internal panel of a door
14.6 Latches of fastening of the internal panel of a door


15.7 Details of a door and стеклоподъемника1. Adjustment двери2. Adjustment of situation door петли3. Adjustment forward желоба4. Mechanism adjustment стеклоподъемника5. Adjustment of situation flew down on стеклоподъемнике6. Clamp adjustment
15.7 Door and window regulator details
1. Door adjustment
2. Adjustment of provision of a door loop
3. Adjustment of a forward trench
4. Adjustment of the mechanism of a window regulator
5. Adjustment of situation flew down on a window regulator
6. Clamp adjustment



9. Insert latches to openings of a framework of a door (by hand or a plastic hammer).
10. Further installation is carried out upside-down. Fix the window regulator handle a spring ring. For this purpose insert a spring ring into a groove on the handle so that the rupture of a ring was turned on 180 ° from the handle, expose the handle parallel to the handle on an opposite door and push a ring before click.


«previous page
16.14. The lock of a back cover and a drive cable - removal and installation
following page»
16.16. Door glass and a window regulator - removal and installation