Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Car maintenance
3. Четырехцилиндровыв engines
4. VS engines
5. All engines
6. Systems of cooling, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
11.1. Specifications
11.2. General data
11.3. Draft of management of transmission - adjustment
11.4. The blocking switch - check and adjustment
11.5. Kick-down - the switch - adjustment
11.6. A rod of a vacuum diaphragm - adjustment
11.7. A back epiploon - replacement
11.8. Automatic transmission - removal and installation
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and furnish elements
17. Electric equipment system
 








11-8-avtomaticheskaya-transmissiya-snyatie-i-ustanovka.html

11.8. Automatic transmission - removal and installation

Attention!
The car should be lifted on sufficient height to get transmission.

All works on repair of transmission are carried out in car-care center.
1. Consider in car-care center codes the malfunctions brought in memory of the processor block, and establish a transmission cause of defect.
2. For transmission removal without dismantle of the engine execute the following operations.
3. Disconnect the battery from weight.
4. Merge transmission liquid.
5. Lift the car and establish on supports.

7.17 Otvorachivaniye of hydrotransformer bolts
7.17 Otvorachivaniye of hydrotransformer bolts


7.25 Sample on the hydrotransformer which should be combined with a ledge on the pump
7.25 Sample on the hydrotransformer which should be combined with a ledge on the pump


6. Remove the driveshaft (Hl. 8) also muffle an opening in transmission.
7. Remove a forward exhaust pipe.
8. Disconnect the socket from the blocking switch.
9. Disconnect the socket from the coil the electric drive; kick-down - a mode.
10. Disconnect a vacuum hose from a diaphragm (is directly in front of the electric drive coil).
11. Disconnect draft from the selector.
12. On a shaft of a case of transmission disconnect a speedometer cable.
13. Disconnect a refueling branch pipe and muffle an opening in transmission.
14. On a shaft of a case of transmission disconnect cooler hoses.
15. Establish under the engine pallet a support and prop up through whetstone.
16. Uncover and designate a relative positioning of a leading disk and the hydrotransformer.
17. Slowly turning the crankshaft, unscrew in turn 4 bolts of fastening of the hydrotransformer.
18. Remove a starter.
19. Drive under transmission the cart with a support and prop up a case.
20. Unscrew bolts of fastening of an arm of a support to transmission.
21. Remove an arm from a body.
22. Unscrew bolts of fastening of transmission to the engine.
23. Lower both supports so that transmission could be separated and removed in the direction to a back part of the car. To remove transmission it is recommended together.
Hand over transmission in repair or replace.

7.24 Check of palpation of a leading disk. If palpation does not correspond to norm, a disk replace
7.24 Check of palpation of a leading disk. If palpation does not correspond to norm, a disk replace


7.27 Check of the adjusting size A of the hydrotransformer
7.27 Check of the adjusting size A of the hydrotransformer


24. Check palpation of a leading disk (photo).
25. Installation is carried out upside-down. Combine sample on the hydrotransformer with a ledge on the pump of transmission liquid (photo).
26. Combine labels on a leading disk and the hydrotransformer, put when dismantling.
27. After installation of the hydrotransformer check the size A (photo) to be convinced of the correct installation of the hydrotransformer.
28. Tighten all bolts with the set moment.
29. Turn a leading disk and be convinced of smoothness of rotation of details of transmission.
30. Fill in liquid.
31. Check operation of all switches and draft of management of transmission. If necessary adjust.

«previous page
11.7. A back epiploon - replacement
following page»
12. Coupling driveshaft and back bridge