Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Car maintenance
3. Четырехцилиндровыв engines
4. VS engines
5. All engines
5.1. General information
5.2. Compression check in engine cylinders
5.3. Dismantle of the power unit - security measures
5.4. The engine - removal and installation
5.5. Major maintenance of the engine - general information
5.6. Engine restoration - alternatives
5.7. Major maintenance of the engine - a dismantling order
5.8. A head of the block of cylinders - dismantling.
5.9. Head of the block of cylinders cleanings and condition check
5.10. A head of cylinders - assembly
5.11. Shatunno-porshnevaya group dismantle
5.12. The crankshaft - dismantle
5.13. The block of cylinders - cleaning
5.14. The block of cylinders - condition check
5.15. Rods and pistons - condition check
5.16. The crankshaft - condition check
5.17. Radical and shatunny bearings - check and selection
5.18. Major maintenance of the engine - an assembly order
5.19. Piston rings - installation
5.20. The crankshaft - installation and check of gaps of radical bearings
5.21. A back epiploon - installation
5.22. Rods and pistons - installation and check of gaps in shatunny bearings
5.23. Engine start-up after repair and a running in
6. Systems of cooling, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and furnish elements
17. Electric equipment system
 








5-16-kolenval-proverka-sostoyaniya.html

5.16. The crankshaft - condition check

1. Wash out a cranked shaft solvent and dry, clean oil channels, necks and remove agnails (photo).
2. Check a condition of necks of a shaft. Measure diameter of necks in several places and define a konusnost and ovality (photo). Check palpation of the crankshaft having established in prisms.
3. In the presence of damages on shaft necks and also if ovality, the konusnost and wear of necks exceed the established limits, the shaft follows перешлифовать and to replace radical and shatunny bearings repair.
4. If on necks under epiploons the deep flute of development from a working edge of an epiploon was formed, there are scratches or other damages, the crankshaft is recommended to replace.

16.1 Remove agnails from edge of a lubricant opening
16.1 Remove agnails from edge of a lubricant opening


15.8 Gap measurement between a flute and a new ring
15.8 Gap measurement between a flute and a new ring


15.9 Measurement of diameter of the piston. Diameter is measured perpendicular to an axis of a finger of 1.20,3 mm
15.9 Measurement of diameter of the piston. Diameter is measured perpendicular to an axis of a finger of 1.20,3 mm


16.2 measurement of diameter of necks of the crankshaft
16.2 measurement of diameter of necks of the crankshaft


17.4а Places of drawing of numbers of dimensional groups of radical bearings on 4-cylinder двигателях1. To a forward part двигателя2. B3 group. Dimensional group of radical necks
17.4а Places of drawing of numbers of dimensional groups of radical bearings on 4-cylinder engines
1. To a forward part of the engine
2. Group B
3. Dimensional group of radical necks



«previous page
5.15. Rods and pistons - condition check
following page»
5.17. Radical and shatunny bearings - check and selection