Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Car maintenance
3. Четырехцилиндровыв engines
4. VS engines
5. All engines
6. Systems of cooling, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
8.1. Specifications
8.2. Ignition system general information
8.3. Ignition system check
8.4. Distributor removal
8.5. Distributor installation
8.6. Sensor of rotation of the crankshaft check
8.7. Ignition coil removal and installation
8.8. System of start-up of the engine general information
8.9. System of start-up of the engine check
8.10. Starter removal and installation
8.11. Traction relay removal and installation
8.12. Starter replacement of brushes
8.13. Charge system general information
8.14. Generator leaving and precautionary measures
8.15. Charge system check
8.16. Generator removal and installation
8.17. Tension and brush regulator replacement
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and furnish elements
17. Electric equipment system
 






8-12-starter-zamena-shhetok.html

8.12. Starter replacement of brushes

Starter without a reducer
1. Remove a starter and the traction relay.
2. Take a back sealant (photo).

11.2б starter Details (without a reducer) rear-wheel cars with 4цилиндровым the engine 1. Traction relay 2. Anchor 3. Sealant 4. Lock washer 5. Persistent washer 6. Back cover 7. Back plug 8. Shchetkoderzhatel 9. Brush () 10. Brush (+) 11. Yoke


11.2в starter Details (without a reducer) all-wheel drive cars with 4цилиндровым the engine 1. Adjusting laying (thickness of 0,5 or 0,8 mm) 2. Traction relay 3. Back cover 4. Yoke 5. Winding of excitement 6. Brush (+) 7. Anchor 8. Shchetkoderzhatel 9. Рыч


11.6 Shchetkoderzhatel starter


11.12 Take away springs and get brushes 1. Shchetkoderzhatel 2. Hook 3. Brush


11.9а starter Details (with a reducer) cars with 4цилиндровым the engine 1. Traction relay 2. Adjusting laying (sealant) 3. Spring 4. Lever 5. Forward cover 6. Case of a reducer 7. Laying 8. Leading gear wheel 9,18. Ring 10. Anchor 11. About


11.9б starter Details (with reducers) cars with the engine V6 1. Traction relay 2. Orbital gear wheel 3. Back cover 4. Sealant 5. Bolt 6. Anchor 7. Yoke 8. Partition 9. Washers 10. Shchetkoderzhatel 11. Planetary gear wheels 12. Leading gear wheel 13. Ш


14.4 Fixing of brushes by a wire piece


3. Get a lock ring and a persistent washer.
4. On a back cover unscrew two screws of a shchetkoderzhatel.
5. Turn out coupling bolts and remove a back cover.
6. Get a shchetkoderzhatel (photo), take away springs and get brushes. If height of brushes less than 12 mm, отпаяйте them also solder the new.
7. Collect a starter upside-down.
Starter with a reducer
8. Remove a starter and the traction relay.
9. Turn out coupling bolts (photo).
10. Remove a back cover, without having damaged a ring.
11. Separate from a cover a yoke assembled with an anchor and a shchetkoderzhatel.
12. Take away springs and get brushes from a shchetkoderzhatel (photo), отпаяйте and solder new (if height of brushes less norm).
13. Collect a starter upside-down.

«previous page
8.11. Traction relay removal and installation
following page»
8.13. Charge system general information