Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Car maintenance
3. Четырехцилиндровыв engines
4. VS engines
5. All engines
6. Systems of cooling, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
13.1. Specifications
13.2. General information
13.3. The device of an automatic interlock of a nave - removal and installation
13.4. Semi-axes - removal and installation
13.5. A semi-axis - dismantling and assembly
13.6. A nave and a rotary fist - smyaty and installation
13.7. Nave epiploons – removal and installation, adjustment of bearings
13.8. The forward driveshaft - removal and installation
13.9. Epiploons of a forward reducer - replacement
13.10. A forward reducer - removal and installation
13.11. Epiploons of a transfer case - replacement
13.12. A transfer case - removal and installation
13.13. A transfer case - dismantling
14. Brake system
15. Suspension brackets and steering
16. Body and furnish elements
17. Electric equipment system
 






13-5-poluos-razborka-i-sborka.html

13.5. A semi-axis - dismantling and assembly

1. Remove a semi-axis.
2. Clamp a semi-axis in a vice through soft laying.

2.5 Check of thickness of blocking rings by L (should be not less than 15,4 mm).


3.11 Semi-axis removal from a rotary fist 1. Whetstone


3.13 Check axial люфта semi-axes


4.3 Dismantling of the internal hinge


4.4 Semi-axis 1 details. From a wheel 2. Details of the CV JOINT of the Rzeppa 3,7,16 type. Lock ring 4. Shaft 5. The Tripod type hinge (the "sliding" hinge) 6. Cap 8. Crosspiece 9. Case 10,13. Cover 11,12,14, Collar 15. Hinge 17. The ring steals up on thicknesses


3. Carefully bring down a semi-axis flange from differential and release a cap of the case of the hinge (photo).
4. Take collars of covers (photo).
5. Displace covers and the case of the sliding hinge towards a wheel pin.
6. Designate the provision of a crosspiece on a semi-axis shaft.
7. Vypressuyte a semi-axis from a crosspiece (it is carried out on the press).
8. Remove a cover and the case.
9. Designate situation on a semi-axis and carefully beat out the external CV JOINT (photo), remove a lock ring.
10. Wash out and examine all details.
11. Before assembly put greasing in the external CV JOINT.
12. Dress a cover on a semi-axis and establish a new lock ring. Put greasing in the external CV JOINT and fix a cover collars.
13. Dress a cover on a semi-axis from differential, collars and establish the case of the internal CV JOINT.
14. Clamp a semi-axis in a vice and establish a crosspiece so that the gear collar of a crosspiece was turned towards a semi-axis.

Attention!
If the removed crosspiece is established, combine the labels put at dismantling. If the new crosspiece is established, displace a crosspiece towards a pin to a limit.

15. Fix a crosspiece on a shaft, расклепав a gear collar in two places (photo). Depth расклепки not less than 1 mm.

4.9 Removal of the external CV JOINT from a semi-axis


4.12 At installation of a cover sustain the size L


4.15 Fixing of a crosspiece of the sliding CV JOINT on a semi-axis shaft, 1. Not less than 1 mm


16. Dress the case and put greasing in the internal CV JOINT
17. Fix a cover a new collar.
18. Put greasing on an epiploon of a cap and establish a cap, screw three bolts and a nut. Vpressuyte a cap, I will hit in three places.
19. Establish the size L of a cover (photo) and level a cover, having removed residual pressure. Fix a small collar.


«previous page
13.4. Semi-axes - removal and installation
following page»
13.6. A nave and a rotary fist - smyaty and installation