Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Car maintenance
3. Четырехцилиндровыв engines
4. VS engines
5. All engines
6. Systems of cooling, heating, ventilation and conditioning
6.1. Cooling system - general information
6.2. Antifreeze - general information
6.3. The thermostat - removal and
6.4. A radiator - removal and installation
6.5. The fan and the coupling - removal and installation
6.6. A tank - removal and
6.7. The pump of cooling liquid - check
6.8. The pump of cooling liquid - removal and installation
6.9. The sensor of temperature of liquid - check and replacement
6.10. Heating system - general information
6.11. The fan - removal and installation
6.12. A heater radiator - removal and installation
6.13. Central air - general information
6.14. Central air - service
6.15. The proof-reader of idling - adjustment
6.16. A moisture separator - removal and installation
6.17. The compressor - removal and installation
6.18. The condenser - removal and installation
6.19. The control panel a heater and the conditioner - removal, installation and adjustment
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and furnish elements
17. Electric equipment system
 








6-12-radiator-otopitelya-snyatie-i-ustanovka.html

6.12. A heater radiator - removal and installation

1. Merge cooling liquid.
2. On cars with the conditioner disconnect shlz-ngi on a partition of a motor compartment (photo)
3. On cars without the conditioner take a casing of a radiator (photo) and disconnect hoses on a partition of a motor compartment.
4. Remove the central section (if it is provided).
5. Disconnect from a fan casing a cable of a delitelny zaslonka.
6. On cars with the conditioner remove the fan, unscrew nuts and bolts of the block of cooling.
7. Unscrew screws and having raised, remove a heater.
8. Remove the control panel (see below).
9. If necessary disassemble a heater for what disconnect drafts of the lever mixing and delitelny a zaslonok, remove latches and disunite both half of a casing (photo). At installation adjust drafts (see below).

11.3б the Fan is established on the right under perchatochny ящиком1. Разъем2. Болт3. Hose
11.3б the Fan is established on the right under a perchatochny box
1. Socket
2. Bolt
3. Hose


12.2 Heater hoses
12.2 Heater hoses


12.3 Details of a heater and кондиционера1,2,13. Defreezing сопло3. Кожух4. Воздухозаборник5,8. Воздуховод6. Nozzles for heating салона7. Bottom air line кондиционера8. Отопитепь10,12. Кронштейн11. Conditioner
12.3 Heater and conditioner details
1,2,13. A defreezing nozzle
3. Casing
4. Air inlet
5,8. Air line
6. Nozzles for salon heating
7. Bottom air line of the conditioner
8. Отопитепь 
10,12. Arm
11. Conditioner


12.9 Radiator of a heater and кожух1. Mixing заслонка2. Drainage кран3. Delitelny заслонка4. Zaslonka ventilating сопла5. Radiator
12.9 Radiator of a heater and casing
1. Mixing zaslonka 
2. Drainage crane
3. Delitelny zaslonka
4. Zaslonka of a ventilating nozzle
5. Radiator



«previous page
6.11. The fan - removal and installation
following page»
6.13. Central air - general information