Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Car maintenance
3. Четырехцилиндровыв engines
4. VS engines
5. All engines
6. Systems of cooling, heating, ventilation and conditioning
6.1. Cooling system - general information
6.2. Antifreeze - general information
6.3. The thermostat - removal and
6.4. A radiator - removal and installation
6.5. The fan and the coupling - removal and installation
6.6. A tank - removal and
6.7. The pump of cooling liquid - check
6.8. The pump of cooling liquid - removal and installation
6.9. The sensor of temperature of liquid - check and replacement
6.10. Heating system - general information
6.11. The fan - removal and installation
6.12. A heater radiator - removal and installation
6.13. Central air - general information
6.14. Central air - service
6.15. The proof-reader of idling - adjustment
6.16. A moisture separator - removal and installation
6.17. The compressor - removal and installation
6.18. The condenser - removal and installation
6.19. The control panel a heater and the conditioner - removal, installation and adjustment
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and furnish elements
17. Electric equipment system
 








6-19-panel-upravleniya-otopitelem-i-kondicionerom-snyatie-ustanovka-i-regulirovka.html

6.19. The control panel a heater and the conditioner - removal, installation and adjustment

1. Disconnect the battery from weight. Remove a tray for trifles (if it is provided).
2. Disconnect from the fan and from a heater cables. It is recommended to transfer the lever of a temperature regulator to the situation Cold.
3. Take from rychazhok of the handle (photo) and remove the control panel.
4. Unscrew screws (photo), get the panel and disconnect sockets.
5. If necessary remove and check the fan switch (Hl. 12). The switch is disconnected from the panel.

17.4 Highways are disconnected from the compressor after an otvorachivaniye of these bolts
17.4 Highways are disconnected from the compressor after an otvorachivaniye of these bolts


19.3 For removal of handles submit them directly on itself.
19.3 For removal of handles submit them directly on itself.


19.3 Remove from rychazhok of the handle and remove the control panel.
19.3 Remove from rychazhok of the handle and remove the control panel.


19.4 Will unscrew screws, get the panel and disconnect sockets.
19.4 Will unscrew screws, get the panel and disconnect sockets.


6. Installation is carried out upside-down. Adjust drafts of management of zaslonka.
Adjustment
7. For adjustment of drafts of a delitelny zaslonka and a zaslonka of a defreezing nozzle at first disconnect a cable of lateral draft and adjust draft of a delitelny zaslonka. Attach a cable and adjust.
8. For adjustment of draft of management by a zaslonka of a ventilating air line displace lateral draft in the direction of an arrow (photo). Holding the top and bottom levers in the bottom situation, attach in the order of draft 1 and 2 to the corresponding levers.
9. For adjustment of draft of management by a zaslonka of a defreezing nozzle displace lateral draft in the direction of an arrow (photo). Having submitted the lever of a zaslonka of a defreezing nozzle in the arrow direction, attach a rod to lateral draft.
10. For adjustment of a cable of management by airinflow submit a cover of a cable and lateral draft in the arrow direction. Fix a cover a collar in this situation.
11. For adjustment of draft of the crane of a heater disconnect from the lever of a mixing zaslonka a cable of a temperature regulator and adjust draft. Attach a cable and adjust. Submit the lever of a mixing zaslonka in the direction of an arrow (photo). Translate draft of the crane of a heater in the arrow direction that between draft and the lever was about 2 mm and attach bent for to the zaslonka lever.

19.10 Adjustment of a cable of management воздухопритоком1. Lateral тяга2. A tax in it направлении3. Хомут4. Extreme situation
19.10 Adjustment of a cable of management by airinflow
1. Lateral draft
2. A tax in this direction
3. Collar
4. Extreme situation


19.8 Adjustment of draft of management by a zaslonka ventilating воздуховода1. Zaslonka lever верхний2. Zaslonka lever нижний3. A tax in it направлении4. Lateral тяга5. Zaslonki 1 and 2
19.8 Adjustment of draft of management by a zaslonka of a ventilating air line
1. Zaslonka lever the top
2. Zaslonka lever the bottom
3. A tax in this direction
4. Lateral draft
5. Zaslonki 1 and 2


19.9 Adjustment of draft of management by a zaslonka defreezing сопла1. Lever заслонки2. Lateral тяга3. A tax in it направлении4. Rod
19.9 Adjustment of draft of management by a zaslonka of a defreezing nozzle
1. Zaslonka lever
2. Lateral draft
3. A tax in this direction
4. Rod


19.11 Adjustment of draft of the crane отопителя1. Подать2. Потянуть3. Lever of draft of management краном4. Тяга5. Lever of a mixing zaslonka
19.11 Adjustment of draft of the crane of a heater
1. Tax
2. To pull
3. Lever of draft of management of the crane
4. Draft
5. Lever of a mixing zaslonka


19.12 Cable adjustment терморегулятора1. Mixing заслонка2. Подать3. Provision of the maximum cooling
19.12 Adjustment of a cable of a temperature regulator
1. Mixing zaslonka
2. Tax
3. Provision of the maximum cooling


12. For adjustment of a cable of a temperature regulator displace a rychazhok to the left (photo), submit a cover of a cable and the zaslonka lever in the direction of an arrow and fix a cover a collar.

19.13 Adjustment of a cable of a zaslonka воздухозаборника1. Zaslonka lever воздухозаборника2. Хомут3. A tax in it направлении4. Situation management rychazhka
19.13 Adjustment of a cable of a zaslonka of an air inlet
1. Lever of a zaslonka of an air inlet
2. Collar
3. A tax in this direction
4. Situation management rychazhka


13. For adjustment of a cable of a zaslonka of an air inlet displace a rychazhok to the full to the left (photo), submit a cover of a cable and the zaslonka lever in the direction of an arrow and fix a cover a collar.

«previous page
6.18. The condenser - removal and installation
following page»
7. Fuel and exhaust systems