Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Car maintenance
3. Четырехцилиндровыв engines
4. VS engines
5. All engines
6. Systems of cooling, heating, ventilation and conditioning
7. Fuel and exhaust systems
7.1. Fuel system - general information
7.2. The fuel filter - replacement
7.3. Idling turns - check and adjustment
7.4. The fuel highway - repair
7.5. A cable of a drive of a butterfly valve - removal and installation
7.6. A pedal - removal and installation
7.7. The fuel pump - check
7.8. The fuel pump - removal and installation
7.9. System of electronic injection of fuel - general information
7.10. Units of control and measuring system with the processor ECCS block - general information
7.11. Decompression of fuel system
7.12. The butterfly valve case (for systems with preliminary injection of TBI of systems) removal and installation
7.13. Nozzle replacement
7.14. System of injection of fuel – adjustments System of preliminary injection (TBI)
7.15. Fuel system cleaning
7.16. Tank removal and installation
7.17. Fuel level sensor removal and installation
7.18. Tank washing
7.19. Exhaust system general information
7.20. Forward exhaust pipe removal and installation
7.21. Catalytic neytralizatorsnyaty and installation
7.22. Exhaust silencer removal and installation
7.23. Average pipe removal and installation
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and furnish elements
17. Electric equipment system
 





Почему лучше всего покупать импортные сигареты именно

7-13-forsunka-zamena.html

7.13. Nozzle replacement

System with preliminary injection
1. Execute a decompression and remove the zaslonka case.
2. Remove from the case laying and a sealant of conducting (photo).
3. Uncover nozzles (photo)

13.3 Screws of a cover of a nozzle 1. Cover 2,3. Screws


13.46 The sizes of an opravka (out of brackets in mm) and the scheme of its arrangement at knocking-out of a nozzle 1. Opravka 2. Plastic hammer 3. The sizes in mm


13.5 At removal of nozzles always change sealing rings 1. Big ring 2. Small ring 3. Rubber ring


13.6б Take aside a uvula and вытолкните a conclusion 1. Screw-driver 2. Uvula 3. Conclusion 4. Вытолкнуть


4. Open a zaslonka and carefully beat out a nozzle in blows on an opravka with internal diameter not less than 5,4 mm (photo). Do not damage a nozzle.
5. If only sealing rings change, replace small and big rubber rings, having greased them with silicone greasing. Establish a nozzle (photo).
6. If the faulty nozzle changes, get from the socket a conclusion of a wire of a faulty nozzle for what do the following:
а), get a clamp of a conclusion (photo),
б), a thin screw-driver take away a uvula and at once вытолкните a conclusion, for a wire not to pull (photo),
в), cut off a wire directly at the plug (photo), previously having determined the necessary wire by the scheme (photo).
7. Stretch a new wire through a sealant and a sleeve (a sealant replace).
8. Dress the plug, attach to a wire a conclusion and press out. Insert a conclusion into the socket being guided by the scheme of distributing (photo).
9. Insert a conclusion into the socket.

13.6а For a conclusion detachment from the socket remove the holder 1. Вытолкнуть


13.6в Cut off a wire at the plug and extend from a sleeve


13.8а Accession of a wire of a nozzle 1. Clamp  2. Wires  3. New nozzle 4. Through sealant 5. Sleeve 6. Plugs 7. Conclusions



Appointment (to a drive)
Number of a conclusion of the socket
Color of a wire
nozzle And (+)
1
G green
nozzle And ()
2
W white
Nozzle In (+)
3
Vsiny
nozzle In ()
4
R red
To the electromagnetic valve of the proof-reader of idling of the conditioner (+)
5
Vsiny
To the electromagnetic valve of the proof-reader of idling of the conditioner ()
6
Vsiny
To the electromagnetic valve of fast idling (+)
7
B/W sinebely
To the electromagnetic valve of fast idling ()
8
B/W sinebely

13.86 The chart, color marking of wires and the scheme of distributing of the socket and wires of nozzles on V6 engines (VG30i) and Z24I (since 1987) with system of preliminary injection


Appointment (to the actuation mechanism (nozzle)
+ nozzles zelenobely
Nozzle And to a conclusion 1
Nozzle In to a conclusion 3
nozzles zheltobely
Nozzle And to a conclusion 2
Nozzle In to a conclusion 4
Numbering of conclusions of the socket

12. Push nozzles, having made effort by hand, overturn the case and be convinced of correctness of installation of nozzles.
13. Grease a sealant of wires (photo).
14. Establish a cover of nozzles, wrap screws, having greased with fixing structure and tighten in a cross order.
15. Grease case laying by silicone structure (the air filter establish only after a skhvatyvaniye of silicone hermetic).
16. Establish the zaslonka case upside-down.
17. Be convinced of lack of a leak, check quality of a mix in car-care center (to be convinced of absence подсоса air through the top sealant of a nozzle).

13.11 Installation of nozzles


13.8в the Arrangement of nozzles and valves on box пусе zaslonka 1,10. Nozzle And 2. Case of a zaslonka 3. Thermoelement 4. To a forward part of the engine 5. Valve of the proof-reader of idling of the conditioner 6. The valve of the raised turns of idling 7,9 Nozzle In 8.


Systems of direct injection
18. Execute a decompression, disconnect батарек; masses also merge liquid.
19. Disconnect wires from candles, uncover ра a predelitel and take wires aside.

13.13 Greasing of a through sealant of wires silicone structure 1. Push


13.20 A soaking-up collector on VS engines


13.25 Details of fastening of a nozzle 1. Rings 2. Isolating plugs


20. Designate and disconnect all sockets of conducting, cables and hoses in a forward part of a soaking-up collector (photo).
21. On V6 engines unscrew bolts and remove soaking-up collector.
22. Disconnect from the distributor with nozzles fuel tubes.
23. Disconnect sockets of nozzles (photo).
24. Remove the distributor with nozzles.
25. Unscrew bolts and get nozzles (photo).
26. Before installation moisten new rings with gasoline and establish new nozzles, having pressed them into the distributor.
27. Establish the distributor assembled with nozzles, turn and tighten bolts.
28. Attach to nozzles sockets.
29. Clear and establish a collector, having replaced laying.
30. Wrap bolts of fastening of a collector to a soaking-up branch pipe. Tighten with the set moment.
31. Attach a retsirkulyatsiya tube, hoses, wires and cables, without breaking their former installation. Attach collars of wires.
32. Establish a pressure regulator. Other operations are carried out upside-down.

13.23 Sockets of nozzles on the V6 engine


14.2 Details for adjustment of the raised turns of idling on the case of a zaslonka 1. Thermoelement 2. Case of a heater 3. Lever of a butterfly valve 4. Adjusting bиht S2 5. Adjusting screw of a butterfly valve 6. Draft of a cam 7. Axis 8 roller.



«previous page
7.12. The butterfly valve case (for systems with preliminary injection of TBI of systems) removal and installation
following page»
7.14. System of injection of fuel – adjustments System of preliminary injection (TBI)