Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Car maintenance
3. Четырехцилиндровыв engines
3.1. General information
3.2. Types of the repair work which is carried out without dismantle of the engine from the car
3.3. An order of installation of the piston of the 1st cylinder in VMT of a step of compression.
3.4. A cover of a head of cylinders - removal and installation
3.5. The roller with yokes - removal and installation
3.6. The roller with yokes - dismantling and assembly
3.7. A cam-shaft - removal and installation
3.8. A cam-shaft, support and yokes - check
3.9. Springs of valves and maslosjemny caps - replacement
3.10. A soaking-up collector - removal and installation
3.11. A final collector - removal and installation
3.12. A head of cylinders - removal
3.13. A head of cylinders - installation
3.14. The oil pump - removal and installation
3.15. The oil pump - check
3.16. A crankshaft pulley - removal and installation
3.17. A forward epiploon of the crankshaft - replacement
3.18. A forward cover - removal and installation
3.19. A chain and asterisks - removal and installation
3.20. The oil pallet - removal and installation
3.21. A flywheel (a leading disk of the hydrotransformer) - removal and installation
3.22. A back epiploon - replacement
3.23. Engine support - replacement
4. VS engines
5. All engines
6. Systems of cooling, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and furnish elements
17. Electric equipment system
 






3-3-poryadok-ustanovki-porshnya-1-go-cilindra-v-vmt-takta-szhatiya.html

3.3. An order of installation of the piston of the 1st cylinder in VMT of a step of compression.

1. On a pulley of the crankshaft the mark for exposure of the piston 1 - го the cylinder in VMT of a step of compression is provided.
2. Piston installation (or pistons) in VMT of a step of compression is an integral part of many procedures.
3. Transfer the check point lever to neutral situation. Disconnect a high-voltage wire of the coil of ignition from the central conclusion of a cover of the distributor and connect to weight on the block of cylinders.

3.5б the Scale on a pulley (K24 engine) 1. Label of red color 2. A scale for ignition installation


4. Uncover the distributor and find on a cover the provision of a high-voltage wire of a candle 1 - го the cylinder. If this conclusion is not numbered, determine it by a wire from a spark plug.
5. Turn the crankshaft a key or a starter so that the mark in a pulley was combined with a label About on a scale. The normal direction of rotation of the engine - clockwise (photo).
5. If the begunok indicates a label put on the case of the distributor, the piston 1 - го the cylinder is in VMT of a step of compression. Otherwise tighten the crankshaft on one complete revolution clockwise (360 °) and establish the piston of the 1st cylinder in VMT of a step of compression.
6. Now it is possible to expose in VMT of a step of compression and other pistons, turning the crankshaft on 180 ° and observing an operating procedure of cylinders.

«previous page
3.2. Types of the repair work which is carried out without dismantle of the engine from the car
following page»
3.4. A cover of a head of cylinders - removal and installation