Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Car maintenance
3. Четырехцилиндровыв engines
3.1. General information
3.2. Types of the repair work which is carried out without dismantle of the engine from the car
3.3. An order of installation of the piston of the 1st cylinder in VMT of a step of compression.
3.4. A cover of a head of cylinders - removal and installation
3.5. The roller with yokes - removal and installation
3.6. The roller with yokes - dismantling and assembly
3.7. A cam-shaft - removal and installation
3.8. A cam-shaft, support and yokes - check
3.9. Springs of valves and maslosjemny caps - replacement
3.10. A soaking-up collector - removal and installation
3.11. A final collector - removal and installation
3.12. A head of cylinders - removal
3.13. A head of cylinders - installation
3.14. The oil pump - removal and installation
3.15. The oil pump - check
3.16. A crankshaft pulley - removal and installation
3.17. A forward epiploon of the crankshaft - replacement
3.18. A forward cover - removal and installation
3.19. A chain and asterisks - removal and installation
3.20. The oil pallet - removal and installation
3.21. A flywheel (a leading disk of the hydrotransformer) - removal and installation
3.22. A back epiploon - replacement
3.23. Engine support - replacement
4. VS engines
5. All engines
6. Systems of cooling, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and furnish elements
17. Electric equipment system
 






3-chetyrekhcilindrovyv-dvigateli.html

3. Четырехцилиндровыв engines




Specifications (all sizes in mm)
Numbering of cylinders
1-2-3-4
Operating procedure
1-3-4-2
Working volume of engines:
The Z24J type (after 1987)
2389 cm3
The KA24E type (after 1990)
2389 cm3
Gaps in valves See GL.1

Z24i if K24 engines (in brackets different data of day of the engine are specified: К24, other data are identical)
Raspredvap

Diameter of basic necks 32,935 - 32,955

Axial люфт
0,2
Sizes of cams
38,477-38,527 (44,839-45,0291
Limiting wear
0,25
Palpation in the center of an average basic neck
0,2
Diameter of support
33,000-33,025
Gap in basic necks of a cam-shaft
0,045-0,090
Oil pump
Gap in gearing of gear wheels:
The standard
0,12
The limiting
0,20
Gap between a conducted gear wheel and the pump case
The standard
0,15-0,21
The limiting
0,50
Face gap 0,06
Deformation of the plane of the case of the pump
no more than 0,03

The inhaling moments (in N of m).
Bolt of an asterisk of a cam-shaft
110-130
Bolts of a natyazhitel and uspokoitel of a chain
6-9 (7-11)
Pulley bolt коленвапа
110-130
Bolts of a head of the block of cylinders:
1st stage of an inhaling
27
2nd stage
70
3rd stage
Completely
to weaken bolts
4th stage
27
5th stage
65-75
Bodta of a final collector
15-18
Bolts of fastening of a flywheel (leading disk of the hydrotransformer)
115-125 (85-96)
Bolts of fastening of a cover of a head of cylinders
1-3 (3,6-7,2)
Bolts of a forward cover (only for Z24i)
bolts М6
4-8
bolts М8
8,5-14
Bolts and nuts of a soaking-up collector
15-18
Bolts and nuts of the oil pallet
4-6
Bolts of the oil pump
10-14
Bolts of rollers of yokes
14-22 (32,4-36)

Order of connection of candles with the distributor on the Z24i engine


Arrangement of cylinders and direction of rotation of the distributor


3.5а the Mark in a pulley division About on a scale for piston installation in VMT.


«previous page
2.46. Oxygen sensor
following page»
3.1. General information