12-15-poluos-zadnijj-kolesnyjj-podshipnik-i-salnik-snyatie-i-ustanovka.html
12.15. A semi-axis, the back wheel bearing and an epiploon - removal and installation.Removal
1. Lift a back part of the car.
2. Remove wheels.
3. Remove a brake drum (Гл.10)
4. Disconnect a cable of the parking brake and the highway of a hydraulic actuator (Гл.10)
5. Unscrew nuts of a board of a brake.
6. Take a semi-axis assembled with a brake (photo). If by hand to get a semi-axis it is not possible, it is necessary to use a shock stripper with an adapter which is established on hairpins of fastening of a wheel.
7. Hook and get an external epiploon (photo). An epiploon it is necessary to change each time at semi-axis removal. A new epiploon press an opravka of suitable diameter.
8. Press the bearing from a semi-axis. This operation is recommended to be carried out in car-care center as the stripper or a press is necessary. If these prisposoleniye are available, execute the following.
|
14.6б Removal of a back semi-axis by means of a shock stripper
|
|
14.9 To Raskontrita a nut of the bearing of a back wheel for what unbend a washer teeth
|
9. Unbend a teeth of a lock washer of a nut of the bearing (photo).
10. Unscrew a bearing nut a vorotkovy key (photo) for what clamp a semi-axis in a vice through a soft pro-rate.
11. By means of a press or a stripper remove a semi-axis from the bearing and a brake board.
12. Beat out an epiploon from an obechayka of the bearing (the epiploon is subject to replacement).
13. If on an external holder of the bearing there are damages, the bearing replace. For this purpose beat out a holder from an obechayka by means of brass a small beard (photo).
|
14.13 Removal of an external holder of the bearing
|
|
14.10 Otvorachivaniye of a nut of the bearing of a back wheel
|
Installation
14. Opravka suitable diameter press in an obechayka a new epiploon of the bearing. Grease working edges of an epiploon with konsistentny greasing.
15. Carefully press an external holder of the bearing in hammer blows on a brass opravka.
16. Establish on a semi-axis the dividing plug so,' that the facet on an opening was turned towards a flange of a semi-axis (photo).
17. By means of a brass opravka carefully press the bearing.
18. Establish ring and lock washers, it is correct сориентируйте and wrap a bearing nut.
19. To Zakontrita a nut, having bent a teeth of a lock washer.
|
14.16 Orientation of the dividing plug of the bearing at installation on a semi-axis 1. Semi-axis 2 flange. Plug
|
|
14.22 Adjusting laying is established between an end face of a beam of the back bridge and the case of the bearing and provides necessary longitudinal люфт semi-axes
|
20. Put konsistentny greasing on the bearing and in a pro-point at an end face of a beam of the back bridge.
21. Grease shlitsa of a semi-axis with transmission oil, put konsistentny greasing on working edges of an epiploon.
22. Establish all taken adjusting laying (photo).
23. If both semi-axes acted in film, establish one of them. Measure longitudinal люфт semi-axes (photo) which should be 0,3-0,9 mm. If люфт does not correspond to norm, adjust, for what remove a semi-axis and add or remove adjusting laying (the thickness of laying is specified Specifications).
24. Establish the second semi-axis (if acted in film) and adjust люфт selection of laying.
25. Further assembly is carried out upside-down.
|
15.5 Otvorachivaniye of bolts of a reducer of the back bridge
|
|
14. 23 Check longitudinal люфта semi-axes
|
|