Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Car maintenance
3. Четырехцилиндровыв engines
4. VS engines
5. All engines
6. Systems of cooling, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
12.1. Specifications
12.2. Coupling - general information
12.3. A coupling pedal - removal, installation and adjustment
12.4. The main cylinder of coupling - removal, dismantling and installation
12.5. The working cylinder of coupling - removal, dismantling and installation
12.6. The Dempferny cylinder of coupling - removal, dismantling and installation
12.7. A coupling hydraulic actuator - removal
12.8. Details of the mechanism of coupling - removal, dismantling and installation
12.9. Vyzhimna the bearing - replacement
12.10. The directing plug of primary shaft of a check point - replacement
12.11. The driveshaft, a reducer and the back bridge - general information
12.12. Kardanny
12.13. An average support - replacement
12.14. Kardannye hinges - replacement
12.15. A semi-axis, the back wheel bearing and an epiploon - removal and installation.
12.16. A reducer of the back bridge - removal and installation
12.17. An epiploon of a leading gear wheel of a reducer - replacement
12.18. Zadny Bridge - removal and installation
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and furnish elements
17. Electric equipment system
 






12-5-rabochijj-cilindr-scepleniya-snyatie-razborka-i-ustanovka.html

12.5. The working cylinder of coupling - removal, dismantling and installation

Removal
1. Wrap a cover from a tank on a polyethylene film to prevent big losses of liquid at a hose detachment.
2. Release a nut of fastening of a tube of a hydraulic actuator to an arm.
4.5 The working cylinder is mounted on a coupling case on the right side


3. Get a spring bracket and remove a hose.
4. Disconnect from the cylinder a hydraulic actuator hose.
5. Unscrew two bolts and remove the cylinder
Dismantling
6. Remove a dustproof cover and get a pusher. Slightly knock with the cylinder on a wooden surface to take a spring and the piston (photo).

4.6 Details of the working cylinder of coupling 1. Pusher 8. Dustproof cover 3. Spring 4. Piston 5 cuff. Piston 6. Cylinder 7. The union for pumping


7. Turn out the union for pumping.
8. Check a condition of an internal surface of the cylinder. At detection задиров, scratches or the painted sites the cylinder replace.

5.1 The Dempferny cylinder is strengthened on a partition of a motor compartment by two screws


5.3 Details of the dempfiruyushchy cylinder 1. Cover 2. Laying 3. Cylinder 4. The union for pumping 5. Internal surface of the cylinder 6. Spring 7. Cuff 8. Piston 9. Persistent surface of a damper 10. Rubber damper


4.9 The correct orientation of the piston, the cylinder and a cuff at assembly


9. If cylinder details in a good condition, wash out them pure brake liquid and replace a sealant (are available on sale in structure ремкомплекта). Dress on the piston a cuff, having tracked correctness of its orientation (photo).
10. Before assembly dip details into brake liquid.
11. Collect the cylinder, having established all details in a former order.
Installation
12. Establish the cylinder upside-down. Remove air from a hydraulic actuator.

«previous page
12.4. The main cylinder of coupling - removal, dismantling and installation
following page»
12.6. The Dempferny cylinder of coupling - removal, dismantling and installation