Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Car maintenance
3. Четырехцилиндровыв engines
4. VS engines
5. All engines
6. Systems of cooling, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
12.1. Specifications
12.2. Coupling - general information
12.3. A coupling pedal - removal, installation and adjustment
12.4. The main cylinder of coupling - removal, dismantling and installation
12.5. The working cylinder of coupling - removal, dismantling and installation
12.6. The Dempferny cylinder of coupling - removal, dismantling and installation
12.7. A coupling hydraulic actuator - removal
12.8. Details of the mechanism of coupling - removal, dismantling and installation
12.9. Vyzhimna the bearing - replacement
12.10. The directing plug of primary shaft of a check point - replacement
12.11. The driveshaft, a reducer and the back bridge - general information
12.12. Kardanny
12.13. An average support - replacement
12.14. Kardannye hinges - replacement
12.15. A semi-axis, the back wheel bearing and an epiploon - removal and installation.
12.16. A reducer of the back bridge - removal and installation
12.17. An epiploon of a leading gear wheel of a reducer - replacement
12.18. Zadny Bridge - removal and installation
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and furnish elements
17. Electric equipment system
 






12-8-detali-mekhanizma-scepleniya-snyatie-razborka-i-ustanovka.html

12.8. Details of the mechanism of coupling - removal, dismantling and installation

1. The increased noise (gnash) at inclusion of transfers or pro-slipping of coupling testify to strong wear of a frictional disk.
2. Wear of coupling strongly depends on a manner of driving of Probuksovk when driving will accelerate wear of a frictional disk the Frictional disk it is recommended to change through each 64000 km of run.
3. For access to coupling it is necessary to remove a transmission (Hl. 7).
4. After removal of a check point examine coupling outside and check a condition of fingers of a diafragmenny spring on a coupling casing. At detection of any damages (deformation or a bend of fingers) replace a coupling casing assembled with a spring.
5. Gradually, in diagonal sequence release bolts, stress of a spring (photo) will not be removed yet. Do not damage a press plate. Fix a flywheel from a provorachivaniye, having inserted a screw-driver into a starter aperture.
6. Turn out bolts, remove a casing of coupling, press a disk and a frictional disk. (photo)
7. Clear of greasing and dirt press a disk, a flywheel and the holder of the bearing.
8. Check a condition of a surface of a press disk existence on it задиров, dents and scratches. Check coстояние of petals of a diafragmenny spring and hollow Check deformation of petals with the help щупа (unevenness of petals on height, a photo), be convinced that this size does not exceed the limit specified in Specifications. At detection of any defects coupling assembled replace.

7.14 Before a tightening of bolts center a frictional disk concerning a flywheel


8.4 Detachment of a spring of a spherical support of a fork of switching off of coupling


9. Check wear of a frictional disk. Replace a disk, if distance from a surface of a frictional slip to heads of rivets less than 0,8 mm or if on a frictional material there are any damages or oil spots.

8. 6 Removal of the vyzhimny bearing


10. Check a condition of a surface of a flywheel. If on it there are superficial damages, прошлифуйте a flywheel. At considerable damages (breakages on a gear wreath, burning out traces on a frictional surface) a flywheel replace (Hl. 2).
11. If on details of coupling oil traces are found, establish the reason and eliminate. If oil is revealed from a coupling casing, replace an epiploon of primary shaft of a check point.
12. Vyzhimna recommends to replace the bearing. Check wear of the directing plug of the bearing, if necessary replace (see below).
13. Before assembly apply a thin film molybdenic greasing on a shlitsa of primary shaft.
14. Before installation of coupling center a frictional disk concerning a flywheel by means of an opravka or the suitable tool (photo).
15. Establish a coupling basket on directing pins. Wrap bolts and tighten in diagonal sequence in some stages before achievement of the set moment (photo).
16. Establish a transmission.

«previous page
12.7. A coupling hydraulic actuator - removal
following page»
12.9. Vyzhimna the bearing - replacement