Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Car maintenance
3. Четырехцилиндровыв engines
4. VS engines
5. All engines
6. Systems of cooling, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
14.1. Specifications
14.2. General information
14.3. Blocks disk (forward and back) brakes - replacement
14.4. A brake support - removal, dismantling and installation
14.5. A brake disk - check, removal and installation
14.6. Back drum-type brakes - replacement of blocks
14.7. The wheel cylinder of back drum-type brakes - removal, dismantling and installation
14.8. See hl. 1
14.9. Disks of back brakes - check, removal and installation
14.10. Blocks of the hand brake (on back disk brakes) - removal, installation and adjustment
14.11. The main cylinder of brakes - removal, dismantling and installation
14.12. A regulator of pressure of brakes - removal and installation
14.13. The hydraulic actuator highway - check and replacement
14.14. Pumping of brakes
14.15. The vacuum amplifier of brakes - general information and check
14.16. The vacuum amplifier of brakes - removal and installation
14.17. The hand brake - adjustment
14.18. The lever of the hand brake - removal and installation
14.19. Cables of the hand brake - removal and installation
14.20. The switch of a signal of braking - removal and installation
14.21. Anti-blocking system (ABS) - general information and access to codes.
15. Suspension brackets and steering
16. Body and furnish elements
17. Electric equipment system
 







2007-2009 . римские шторы на кухню | На сайте sillage-original.ru house of sillage. | Проститутки Самары по материалам malinki163.biz.

14-10-kolodki-ruchnogo-tormoza-na-zadnikh-diskovykh-tormozakh.html

14.10. Blocks of the hand brake (on back disk brakes) - removal, installation and adjustment

Removal
1. Remove a disk of a back brake.
2. Remove clamping springs of blocks for what press a cap and turn on 90 ° (photo).
3. Displace blocks from a board of a brake (photo), remove two springs, directing and a strut.
4. Dissolve blocks in the top part and remove from a semi-axis flange, disconnect a cable of the hand brake from the lever
5. Remove a spring and a regulator, wash out details in solvent and grease a carving part with konsistentny greasing.
6. If blocks change, establish the conducted lever of the hand brake on a new block.

9.2 Details of the hand brake of back disk brakes 1. Fingers of clamping springs 2. Board of a brake 3. Regulator 4. Adjusting spring 5. Contact surfaces 6. Basic washer 7. Spring 8. Cap of a clamping spring 9. Spring 10. Strut 11. возвратны
9.2 Details of the hand brake of back disk brakes 1. Fingers of clamping springs 2. Board of a brake 3. Regulator 4. Adjusting spring 5. Contact surfaces 6. Basic washer 7. Spring 8. Cap of a clamping spring 9. Spring 10. Strut 11. возвратны


9.3 Release blocks, submit on itself and remove returnable springs
9.3 Release blocks, submit on itself and remove returnable springs


Installation
7. Hook on a regulator spring for a block and establish a regulator. Be convinced that grooves on a regulator came into end faces of blocks.
8. Slightly grease those places of blocks which adjoin to a board of a brake (photo).
9. Attach a cable to the lever on a block.
10. Dissolve blocks and establish, having pressed to a brake board. Establish a strut.
11. Establish clamping springs of blocks, fix caps, having turned them on 90 °.
12. Establish springs and directing.
13. Establish a disk on a flange of a semi-axis and fix, having screwed two nuts of a wheel. Establish the cylinder and a support.
Adjustment
14. Check that the hand brake is completely released. Get a cap in a board and having inserted a screw-driver, rotate a regulator for a teeth until then while the block will not adjoin to a drum of a disk (photo).
15. Unscrew a regulator in the opposite direction on 7-8 clicks and be convinced that the disk rotates freely, without touching a block.
16. Put a cap into place.

9.14 Remove a cap and a screw-driver rotate a regulator for a teeth until then while the block will not adjoin to a disk drum, then unscrew a regulator in the opposite direction on 7-8 clicks. 1. Cap of a regulator 2. Screw-driver 3. To take away a block
9.14 Remove a cap and a screw-driver rotate a regulator for a teeth until then while the block will not adjoin to a disk drum, then unscrew a regulator in the opposite direction on 7-8 clicks. 1. Cap of a regulator 2. Screw-driver 3. To take away a block


9.7 Greasing places on a brake board
9.7 Greasing places on a brake board




«previous page
14.9. Disks of back brakes - check, removal and installation
following page»
14.11. The main cylinder of brakes - removal, dismantling and installation