Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Car maintenance
3. Четырехцилиндровыв engines
4. VS engines
5. All engines
6. Systems of cooling, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
14.1. Specifications
14.2. General information
14.3. Blocks disk (forward and back) brakes - replacement
14.4. A brake support - removal, dismantling and installation
14.5. A brake disk - check, removal and installation
14.6. Back drum-type brakes - replacement of blocks
14.7. The wheel cylinder of back drum-type brakes - removal, dismantling and installation
14.8. See hl. 1
14.9. Disks of back brakes - check, removal and installation
14.10. Blocks of the hand brake (on back disk brakes) - removal, installation and adjustment
14.11. The main cylinder of brakes - removal, dismantling and installation
14.12. A regulator of pressure of brakes - removal and installation
14.13. The hydraulic actuator highway - check and replacement
14.14. Pumping of brakes
14.15. The vacuum amplifier of brakes - general information and check
14.16. The vacuum amplifier of brakes - removal and installation
14.17. The hand brake - adjustment
14.18. The lever of the hand brake - removal and installation
14.19. Cables of the hand brake - removal and installation
14.20. The switch of a signal of braking - removal and installation
14.21. Anti-blocking system (ABS) - general information and access to codes.
15. Suspension brackets and steering
16. Body and furnish elements
17. Electric equipment system
 






14-6-zadnie-barabannye-tormoza-zamena-kolodok.html

14.6. Back drum-type brakes - replacement of blocks

1. Lift a back part of the car and establish on supports. Release the hand brake.
2. Remove a wheel.
3. If necessary reduce blocks a regulator (Hl. 1)
4. Remove a drum for what rotating a drum, knock on it with a hammer with soft brisk in the direction outside. If the drum does not give in to removal, displace it, evenly wrapping bolts М8 x 1,25 in special carving openings (photo).

4.5б Check of thickness of a disk. Measure thickness in several places


4.13б disk and nave Division


5.4 Drum removal by means of auxiliary bolts


5. Carefully clear a drum of a dust and dirt.
6. Remove clamping springs of blocks for what press a cap and turn on 90 ° (photo).
7. Take the top coupling springs of blocks (photo).
8. Dissolve blocks and get a strut (photo).

5.6 Removal of clamping springs of blocks


9. In addition dissolve blocks and get them from grooves in a regulator and pistons. Fix pistons from a vydviganiye from cylinders (that at assembly not to pump over a hydraulic actuator).
10. Disconnect from the lever a cable of the hand brake.
11. A pedal of a brake do not press, otherwise pistons leave the cylinder.
12. Check a condition of covers of the cylinder and existence of a leak of liquid. If necessary repair or replace cylinders.

5.7б the Top spring directing and a cable of peгулятора


13. Grease a carving of a regulator of blocks brake liquid.
14. Before assembly slightly grease rubbing places ю boats with brake greasing, without allowing hit on pi zinovy details.
5.7а Details of a back drum-type brake of the polnopoivolny car of "Terrann I/Pathfinder" 1. Adjusting lever 2. Spring 3. Basic washer of a spring 4. Clamping spring 5. Cap of a spring 6. Reel 7. An adjusting cable with a spring 8,14. Spring 9,12


5.8 Removal of a strut of blocks


5.16 Marking with the indication of limiting internal diameter of a drum


15. Establish springs, enter into a regulator groove the bottom end face of a back block then the bottom end face of a forward block, move apart blocks and enter into grooves of pistons of the wheel cylinder. Establish other details (photo).
16. Establish a drum and a wheel.
17. Adjust a gap between blocks and drums having several times lifted and having lowered the lever of the hand brake. If necessary remove air from brakes. Lower the car.


«previous page
14.5. A brake disk - check, removal and installation
following page»
14.7. The wheel cylinder of back drum-type brakes - removal, dismantling and installation