Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Car maintenance
3. Четырехцилиндровыв engines
4. VS engines
5. All engines
6. Systems of cooling, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
14.1. Specifications
14.2. General information
14.3. Blocks disk (forward and back) brakes - replacement
14.4. A brake support - removal, dismantling and installation
14.5. A brake disk - check, removal and installation
14.6. Back drum-type brakes - replacement of blocks
14.7. The wheel cylinder of back drum-type brakes - removal, dismantling and installation
14.8. See hl. 1
14.9. Disks of back brakes - check, removal and installation
14.10. Blocks of the hand brake (on back disk brakes) - removal, installation and adjustment
14.11. The main cylinder of brakes - removal, dismantling and installation
14.12. A regulator of pressure of brakes - removal and installation
14.13. The hydraulic actuator highway - check and replacement
14.14. Pumping of brakes
14.15. The vacuum amplifier of brakes - general information and check
14.16. The vacuum amplifier of brakes - removal and installation
14.17. The hand brake - adjustment
14.18. The lever of the hand brake - removal and installation
14.19. Cables of the hand brake - removal and installation
14.20. The switch of a signal of braking - removal and installation
14.21. Anti-blocking system (ABS) - general information and access to codes.
15. Suspension brackets and steering
16. Body and furnish elements
17. Electric equipment system
 








14-7-kolesnyjj-cilindr-zadnikh-barabannykh-tormozov-snyatie-razborka-i-ustanovka.html

14.7. The wheel cylinder of back drum-type brakes - removal, dismantling and installation

1. Prepare ремкомплект the cylinder.
2. Remove drums and blocks.
3. Substitute the pallet.

5.15 Back brake of the all-wheel drive car
5.15 Back brake of the all-wheel drive Terrano I/Pathfinder car assembled.


6.4 Union of a tube of a brake
6.4 Union of a tube of a brake


4. Clear bolts of fastening of the cylinder to a board of a brake and the union (photo). Unscrew the union and muffle a tube and an opening in the cylinder.
5. Unscrew 4 nuts of fastening of the cylinder and remove spring washers. Get the cylinder.
6. When dismantling remove covers, get heads of pistons and pistons. Take from pistons of a cuff (photo).
7. Check a condition of details, existence of scratches on the cylinder because of pollution in liquid.
8. If a cylinder condition satisfactory, wash out it brake liquid.
9. Grease new cuffs with liquid and establish on pistons so that edges of cuffs were turned in the cylinder. Collect the cylinder.
10. Further assembly is carried out upside-down. Pump over a hydraulic actuator of brakes and remove air.

6.6 It is put/m the wheel cylinder 1. Cover 2. Gotha пщшшт Z.Parshvn 4. Cuffs 5. Cylinder 6. Union дпя pumpings 7. Cap
6.6 It is put/m the wheel cylinder 1. Cover 2. Gotha пщшшт Z.Parshvn 4. Cuffs 5. Cylinder 6. Union дпя pumpings 7. Cap



«previous page
14.6. Back drum-type brakes - replacement of blocks
following page»
14.8. See hl. 1