Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Car maintenance
3. Четырехцилиндровыв engines
4. VS engines
5. All engines
6. Systems of cooling, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
14.1. Specifications
14.2. General information
14.3. Blocks disk (forward and back) brakes - replacement
14.4. A brake support - removal, dismantling and installation
14.5. A brake disk - check, removal and installation
14.6. Back drum-type brakes - replacement of blocks
14.7. The wheel cylinder of back drum-type brakes - removal, dismantling and installation
14.8. See hl. 1
14.9. Disks of back brakes - check, removal and installation
14.10. Blocks of the hand brake (on back disk brakes) - removal, installation and adjustment
14.11. The main cylinder of brakes - removal, dismantling and installation
14.12. A regulator of pressure of brakes - removal and installation
14.13. The hydraulic actuator highway - check and replacement
14.14. Pumping of brakes
14.15. The vacuum amplifier of brakes - general information and check
14.16. The vacuum amplifier of brakes - removal and installation
14.17. The hand brake - adjustment
14.18. The lever of the hand brake - removal and installation
14.19. Cables of the hand brake - removal and installation
14.20. The switch of a signal of braking - removal and installation
14.21. Anti-blocking system (ABS) - general information and access to codes.
15. Suspension brackets and steering
16. Body and furnish elements
17. Electric equipment system
 







5355-78

14-4-support-tormoza-snyatie-razborka-i-ustanovka.html

14.4. A brake support - removal, dismantling and installation

Attention!
Described operations belong to the brakes, the equipped both one-piston and block (two-piston) cylinders.

1. Remove blocks.
2. Unscrew the hose union on a support (photo), disconnect and muffle a hose.
3. Unscrew the top bolt of a support and remove a support from a disk.
4. Clear a support, observing safety rules.
5. Carefully remove pistons with the compressed air (photo), previously having wound the cylinder with rags.

2. 2а Disk тоомоз CL25VA (rear-wheel and/m with 4-cylinder engines) 1. Copper laying 2. Cylinder 3. Cuff 4. Piston 5. Cover 6. External laying 7. Blocks 8. Holders 9. Support 10. Finger. To grease a sliding part 11. Caps 12. Вн
2. 2а Disk тоомоз CL25VA (rear-wheel and/m with 4-cylinder engines) 1. Copper laying 2. Cylinder 3. Cuff 4. Piston 5. Cover 6. External laying 7. Blocks 8. Holders 9. Support 10. Finger. To grease a sliding part 11. Caps 12. Вн


2.2в Bolt of the bottom axis
2.2в Bolt of the bottom axis


2.3 Otkidyvaniye of a support for access to blocks 1. Cylinder 2. Block 3. Holders
2.3 Otkidyvaniye of a support for access to blocks 1. Cylinder 2. Block 3. Holders


2.2б the Disk brake of CL25VD (all all-wheel drive and/m and all and/m with V6 engines) 1. Hose 2. Cap 3. The union for pumping 4. Cylinder 5. Cuffs 6. Piston 7. Cover 8. External laying 9,17. Block 10. Holders 11. Support 12. On sites соприкасающ
2.2б the Disk brake of CL25VD (all all-wheel drive and/m and all and/m with V6 engines) 1. Hose 2. Cap 3. The union for pumping 4. Cylinder 5. Cuffs 6. Piston 7. Cover 8. External laying 9,17. Block 10. Holders 11. Support 12. On sites соприкасающ


2.5 Greasing points silicone structure 1. Greasing place
2.5 Greasing points silicone structure 1. Greasing place


2.7 Support shift for installation of external laying
2.7 Support shift for installation of external laying


2.8 Greasing of holders of blocks 1. Greasing place
2.8 Greasing of holders of blocks 1. Greasing place


3.5 Piston removal from the cylinder the compressed air
3.5 Piston removal from the cylinder the compressed air


3.6 Extraction of a cuff 1. Support 2. A flute in the cylinder 3. Cuff 4. Plastic tweezers
3.6 Extraction of a cuff 1. Support 2. A flute in the cylinder 3. Cuff 4. Plastic tweezers


3.2 Unscrew a bolt and disconnect the union. Copper laying is subject to replacement
3.2 Unscrew a bolt and disconnect the union. Copper laying is subject to replacement


6. Carefully get from the cylinder a cuff (photo).
7. Turn out the union for pumping, get from a support fingers and covers.
8. Wash out and dry details.
9. Check a condition of pistons and an internal surface of the cylinder. At detection of appreciable damages, wear of a covering of a detail replace. At corrosion detection on bolts replace bolts.
10. At assembly grease the piston and the cylinder with brake liquid, establish a new cuff (photo).
11. Dress on the piston a cover, having laid in a flute (photo).
12. Enter the piston into the cylinder without distortions, then having pressed drown the piston against the stop in a bottom of the cylinder (photo).
13. Establish a cover on the cylinder.
14. Wrap the union for pumping
15. Grease fingers with silicone greasing and establish with new covers in a support.
16. Further operations are carried out upside-down. Remove air from a hydraulic actuator of an understanding brake.

3.10 Installation of a cuff 1. Support 2. Cuff 3. Flute
3.10 Installation of a cuff 1. Support 2. Cuff 3. Flute


3.11 Cover installation on the piston
3.11 Cover installation on the piston


4.3. Surface of a disk of a brake
4.3. Surface of a disk of a brake




«previous page
14.3. Blocks disk (forward and back) brakes - replacement
following page»
14.5. A brake disk - check, removal and installation