Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Car maintenance
3. Четырехцилиндровыв engines
4. VS engines
5. All engines
6. Systems of cooling, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
12.1. Specifications
12.2. Coupling - general information
12.3. A coupling pedal - removal, installation and adjustment
12.4. The main cylinder of coupling - removal, dismantling and installation
12.5. The working cylinder of coupling - removal, dismantling and installation
12.6. The Dempferny cylinder of coupling - removal, dismantling and installation
12.7. A coupling hydraulic actuator - removal
12.8. Details of the mechanism of coupling - removal, dismantling and installation
12.9. Vyzhimna the bearing - replacement
12.10. The directing plug of primary shaft of a check point - replacement
12.11. The driveshaft, a reducer and the back bridge - general information
12.12. Kardanny
12.13. An average support - replacement
12.14. Kardannye hinges - replacement
12.15. A semi-axis, the back wheel bearing and an epiploon - removal and installation.
12.16. A reducer of the back bridge - removal and installation
12.17. An epiploon of a leading gear wheel of a reducer - replacement
12.18. Zadny Bridge - removal and installation
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and furnish elements
17. Electric equipment system
 






12-13-srednyaya-opora-zamena.html

12.13. An average support - replacement

1. Unscrew two nuts of an arm of a support, remove both half of an arm.
2. Designate a relative positioning of flanges of forward and back sections of the driveshaft (photo).

11.2 Before a detachment of the driveshaft designate the mutual provision of flanges


12.2 Designation of a relative positioning of flanges of sections of a shaft


12.3 Fix the driveshaft and unscrew bolts of flanges of forward and back sections


12.5а a flange Nut законтрена wreath cave-in in a groove of a carving part of a shaft


3. Fix the driveshaft and unscrew bolts of flanges of forward and back sections (photo).
4. Designate the provision of a flange concerning a groove on a carving part of a shaft.
5. Unscrew a nut of a flange of the kardanny hinge for what correct раскерненнуго a part of a wreath of a nut (photo), screw in a flange bolts and fix shaft section from a provorachivaniye (photo). 6. Take a flange (photo).
7. Remove an average support by means of a hydraulic press (выпрессовать an average support and to press new it is recommended in car-care center).
8. At a zapressovyvaniye of an average support, be convinced that the letter "Is turned by R to a forward part of the car.
9. Apply a thin film konsistentny greasing on an end face of an average support and a washer. Establish a washer into place.
10. Combine a flange label with a groove. Establish a flange.
11. Wrap a lock-nut and tighten with the set moment, then законтрите, having pressed a nut wreath into a groove of a carving part of a shaft (photo).
12. Combine labels on flanges and wrap bolts.
13. Further operations on assembly are carried out upside-down. At installation of an arm of an average support keep in mind that the joint in a rubber pillow of the bearing of a support should be turned up.

12.11 Two types of nuts of a flange of an average support – with a fillet (at the left), a standard nut with a washer (on the right)


12.5б Otvorachivaniye of a flange nut


12.6 Removal of a flange of an average support from the forward driveshaft



«previous page
12.12. Kardanny
following page»
12.14. Kardannye hinges - replacement