Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Car maintenance
3. Четырехцилиндровыв engines
4. VS engines
5. All engines
6. Systems of cooling, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
12.1. Specifications
12.2. Coupling - general information
12.3. A coupling pedal - removal, installation and adjustment
12.4. The main cylinder of coupling - removal, dismantling and installation
12.5. The working cylinder of coupling - removal, dismantling and installation
12.6. The Dempferny cylinder of coupling - removal, dismantling and installation
12.7. A coupling hydraulic actuator - removal
12.8. Details of the mechanism of coupling - removal, dismantling and installation
12.9. Vyzhimna the bearing - replacement
12.10. The directing plug of primary shaft of a check point - replacement
12.11. The driveshaft, a reducer and the back bridge - general information
12.12. Kardanny
12.13. An average support - replacement
12.14. Kardannye hinges - replacement
12.15. A semi-axis, the back wheel bearing and an epiploon - removal and installation.
12.16. A reducer of the back bridge - removal and installation
12.17. An epiploon of a leading gear wheel of a reducer - replacement
12.18. Zadny Bridge - removal and installation
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and furnish elements
17. Electric equipment system
 








12-9-vyzhimnojj-podshipnik-zamena.html

12.9. Vyzhimna the bearing - replacement

1. At repair or replacement of details of coupling it is necessary to replace vyzhimny the bearing, or to perform works on its service.
2. If the greasing exit from the bearing is observed, or the bearing is hardly turned by hand, it is necessary to replace it.
3. Remove a rubber cover of a fork of coupling.
4. Disconnect a screw-driver a spring of a spherical support of a fork (photo).
5. Remove a fork of switching off of coupling.
6. Take vyzhimny the bearing (photo).

Attention!
Check existence on a fork of cracks and deformations. Check freedom of rotation of the bearing by hand. Vyzhimna the bearing cannot be washed out and in solvent. At installation of new coupling vyzhimny it is necessary to replace the bearing.

7. If necessary press vyzhimny the bearing from a nave (photo).

8.7 Vypressovyvaniye of the vyzhimny bearing from a nave
8.7 Vypressovyvaniye of the vyzhimny bearing from a nave


8.9 Put greasing in an internal cavity of a nave, grease the places specified by arrows 1. To put greasing
8.9 Put greasing in an internal cavity of a nave, grease the places specified by arrows 1. To put greasing


9.5 Removal of the directing plug by a special stripper
9.5 Removal of the directing plug by a special stripper


8. Press the new bearing, putting effort to an external holder.
9. Assembly is carried out upside-down. Put refractory greasing in an internal cavity of a nave (photo).
10. Apply a thin film the same greasing on rubbing surfaces of a fork. Superfluous greasing is not allowed
11. At fork installation on vyzhimny the bearing be convinced that the terminations of a spring came into a pro-point of the bearing and rest against a fork (photo).

9.6 Removal of the directing plug by hydroblow
9.6 Removal of the directing plug by hydroblow


8.11 Fixing of the vyzhimny bearing by a spring on a fork of switching off of coupling
8.11 Fixing of the vyzhimny bearing by a spring on a fork of switching off of coupling



«previous page
12.8. Details of the mechanism of coupling - removal, dismantling and installation
following page»
12.10. The directing plug of primary shaft of a check point - replacement