Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Car maintenance
3. Четырехцилиндровыв engines
4. VS engines
5. All engines
6. Systems of cooling, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
12.1. Specifications
12.2. Coupling - general information
12.3. A coupling pedal - removal, installation and adjustment
12.4. The main cylinder of coupling - removal, dismantling and installation
12.5. The working cylinder of coupling - removal, dismantling and installation
12.6. The Dempferny cylinder of coupling - removal, dismantling and installation
12.7. A coupling hydraulic actuator - removal
12.8. Details of the mechanism of coupling - removal, dismantling and installation
12.9. Vyzhimna the bearing - replacement
12.10. The directing plug of primary shaft of a check point - replacement
12.11. The driveshaft, a reducer and the back bridge - general information
12.12. Kardanny
12.13. An average support - replacement
12.14. Kardannye hinges - replacement
12.15. A semi-axis, the back wheel bearing and an epiploon - removal and installation.
12.16. A reducer of the back bridge - removal and installation
12.17. An epiploon of a leading gear wheel of a reducer - replacement
12.18. Zadny Bridge - removal and installation
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and furnish elements
17. Electric equipment system
 








12-14-kardannye-sharniry-zamena.html

12.14. Kardannye hinges - replacement

Attention!
Hinges on a part of cars to replacement are not subject to Kardannye. Before dismantling kardanny a shaft consult at the supplier of spare parts.

Lock rings of bearings of crosspieces are picked up for thickness. Not to break driveshaft balancing new lock rings of crosspieces should be just the same thickness, as replaced (see. "Specifications")

13.2 To remove a lock ring, beat out егс in hammer blows on a screw-driver
13.2 To remove a lock ring, beat out егс in hammer blows on a screw-driver


13.3 Vypressovyvaniye of crosspiece bearings
13.3 Vypressovyvaniye of crosspiece bearings


14.6а Poluos and back bridge 1. Epiploon 2. Nut of the wheel bearing 3. Lock washer of the wheel bearing 4. Washer 5. Wheel bearing 6. Dividing plug 7. Bearing 8 holder. Epiploon 9. Semi-axis 10. Refueling opening 11. Sapun 12. Slivn
14.6а Poluos and back bridge 1. Epiploon 2. Nut of the wheel bearing 3. Lock washer of the wheel bearing 4. Washer 5. Wheel bearing 6. Dividing plug 7. Bearing 8 holder. Epiploon 9. Semi-axis 10. Refueling opening 11. Sapun 12. Slivn


13.6 Installation of lock rings
13.6 Installation of lock rings


1. Designate a relative positioning of all details of hinges.
2. Clear a fork of dirt and get lock rings (photo).
3. Beat out bearings of crosspieces in hammer blows with soft brisk (photo) on a fork.
4. Get a crosspiece.
5. Check люфт bearings in necks of crosspieces, worn-out details replace.
6. Assembly is carried out upside-down.

Attention!
Before installation grease lock rings with konsistentny greasing Establish lock rings on former places (photo), considering that the thickness of lock rings opposite bearings should not differ more than on 0,06 mm.


«previous page
12.13. An average support - replacement
following page»
12.15. A semi-axis, the back wheel bearing and an epiploon - removal and installation.