Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Car maintenance
3. Четырехцилиндровыв engines
4. VS engines
5. All engines
6. Systems of cooling, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
12.1. Specifications
12.2. Coupling - general information
12.3. A coupling pedal - removal, installation and adjustment
12.4. The main cylinder of coupling - removal, dismantling and installation
12.5. The working cylinder of coupling - removal, dismantling and installation
12.6. The Dempferny cylinder of coupling - removal, dismantling and installation
12.7. A coupling hydraulic actuator - removal
12.8. Details of the mechanism of coupling - removal, dismantling and installation
12.9. Vyzhimna the bearing - replacement
12.10. The directing plug of primary shaft of a check point - replacement
12.11. The driveshaft, a reducer and the back bridge - general information
12.12. Kardanny
12.13. An average support - replacement
12.14. Kardannye hinges - replacement
12.15. A semi-axis, the back wheel bearing and an epiploon - removal and installation.
12.16. A reducer of the back bridge - removal and installation
12.17. An epiploon of a leading gear wheel of a reducer - replacement
12.18. Zadny Bridge - removal and installation
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and furnish elements
17. Electric equipment system
 






12-17-salnik-vedushhejj-shesterni-reduktora-zamena.html

12.17. An epiploon of a leading gear wheel of a reducer - replacement

1. Merge from a reducer oil.
2. Lift a back part of the car, we will establish supports under a frame and a reducer case.
3. Disconnect from a reducer the driveshaft and displace aside.
4. Fix a reducer flange mount or a big screw-driver, having screwed bolts, and unscrew a nut of a leading gear wheel.
5. Take a flange of a reducer (photo).
6. Hook and take an epiploon (photo).
7. Grease an epiploon and a pro-point in a case a reducer! Konsistentny greasing. Accurately, without allowing a smeshcheiya of a leading gear wheel of a reducer, press a new epiploon; so that its surface became aflush with a case (sponges of an epiploon should be turned inside).

16.5 Removal of a flange of a reducer by means of a stripper


8. Establish a reducer flange, a persistent washer and wrap a nut.
9. Having fixed a reducer flange, tighten a nut before disappearance axial люфта a leading gear wheel.
10. Turn a leading gear wheel of a reducer several times in both directions. By means of a dinamometrichesky key with a scale in some N of m also measure torque size at which leading gear wheel it starts to be turned. This moment is equal to a preliminary tightness in bearings of a leading gear wheel and should correspond specified in Specifications. If the moment appears less demanded, tighten a reducer nut until then the necessary moment will not be reached yet.

16.6 Extraction of an epiploon of a reducer


Attention!
The preliminary tightness is provided with the rasporny plug of bearings of a leading gear wheel. If the size of a preliminary tightness more recommended, the plug is deformed. In this case a reducer it is necessary to remove and replace the rasporny plug.

17.8 Zadny Bridge (shooters specified assorted connections at bridge removal)


11. Further assembly is carried out upside-down.
12. Upon termination of fill in in a reducer oil.

«previous page
12.16. A reducer of the back bridge - removal and installation
following page»
12.18. Zadny Bridge - removal and installation