Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Car maintenance
3. Четырехцилиндровыв engines
4. VS engines
5. All engines
6. Systems of cooling, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
15.1. Specifications
15.2. General information
15.3. Hairpins of fastening of a wheel - replacement
15.4. The stabilizer - removal and installation
15.5. Shock-absorbers - removal and installation
15.6. Torsion - removal and installation
15.7. Bars and suspension bracket extensions - removal and installation
15.8. The top lever and a spherical support - removal and installation
15.9. The bottom lever and a spherical support - removal and installation
15.10. Springs of a back suspension bracket - removal and installation
15.11. Bars of a back suspension bracket - removal and
15.12. The stabilizer of a back suspension bracket - removal and installation
15.13. A steering - general information
15.14. A wheel - removal and installation
15.15. The lock of a steering column - removal and installation
15.16. A steering reducer - removal and installation
15.17. A steering reducer (and/m without the hydraulic booster) - dismantling
15.18. Steering
15.19. The pump hydraulic boosters - removal and installation
15.20. Air removal from a wheel hydraulic actuator
15.21. Steering drafts - removal and installation
15.22. Corners of installation of forward wheels - general information
15.23. Wheels and tires - general information
16. Body and furnish elements
17. Electric equipment system
 








15-8-verkhnijj-rychag-i-sharovaya-opora-snyatie-i-ustanovka.html

15.8. The top lever and a spherical support - removal and installation

1. Will lift a car front.
2. Remove a wheel.
3. Unscrew the top nut of the shock-absorber and compress the shock-absorber.
4. Slightly raise a jack the bottom lever.
5. Release a nut of the top hinge. Vypressuyte a stripper a support finger from an eye of a fist (photo). Unscrew a nut.
6. Unscrew bolts of fastening of an axis of the lever to a frame and remove the lever assembled with a support and adjusting washers. Pay attention to quantity and an order of an arrangement of adjusting washers (photo).
7. Unscrew nuts and remove a support. The support not folding and in case of wear is replaced entirely.

7.5б the Elementary adaptation for the support vypressovka, made of a bolt, a nut and a face head
7.5б the Elementary adaptation for the support vypressovka, made of a bolt, a nut and a face head


7.5а Vypressovka of a finger of the top support by means of the adaptation
7.5а Vypressovka of a finger of the top support by means of the adaptation



8. The hardened or damaged plugs of the lever replace. For this purpose unscrew nuts of an axis and выпрессуйте an axis from the lever (the press is required).
9. Before a press fitting of new plugs moisten them with soap solution. Plugs are pressed on a hydraulic press so that the fillet on the plug rested against reciprocal deepening in a lever sleeve.
10. Insert an axis and dress internal washers so that their rounded parties were turned inside.
11. Press external plugs.
12. Wrap axis nuts.
13. Establish on the lever a support.
14. Establish the lever, having tracked safety of adjusting washers. Tighten bolts with the set moment.

7.6 Bolts of fastening of an axis of the top lever of a suspension bracket
7.6 Bolts of fastening of an axis of the top lever of a suspension bracket


7.15 Check lever centering, having measured the sizes A and B
7.15 Check lever centering, having measured the sizes A and B


8.8 Nut of an axis of the bottom lever
8.8 Nut of an axis of the bottom lever


9.3 Details of a back suspension bracket 1. Cross-section bar 2. Longitudinal bar 3. Top bar 4. Draft of the stabilizer 5. Stabilizer 6. At a wraparound of bolts and nuts correctly them сориентируйте. Bolts and nuts should correspond the established manufacturer.
9.3 Details of a back suspension bracket 1. Cross-section bar 2. Longitudinal bar 3. Top bar 4. Draft of the stabilizer 5. Stabilizer 6. At a wraparound of bolts and nuts correctly them сориентируйте. Bolts and nuts should correspond the established manufacturer.


15. Check the sizes A and B (photo). Compare them with specified in Specifications, if necessary adjust.
16. Other operations are carried out upside-down. Bolts and nuts finally tighten after car lowering on wheels. Check and adjust corners of installation of wheels.


«previous page
15.7. Bars and suspension bracket extensions - removal and installation
following page»
15.9. The bottom lever and a spherical support - removal and installation