Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Car maintenance
2.1. Introduction
2.2. Maintenance terms
2.3. An order of performance of adjustments - general comments
2.4. Check of level of liquids
2.5. Check of level of liquid in automatic transmission
2.6. Check of level of liquid of the power steering
2.7. Check of tires (through each 400 kilometers or weekly)
2.8. Care of the battery
2.9. Care of cooling system
2.10. Check of brushes of screen wipers
2.11. Check of a condition of the hoses located in a motor compartment.
2.12. Check and adjustment of a pedal of a brake
2.13. Replacement of oil and oil filter
2.14. Check and adjustment of gaps of valves
2.15. Greasing of a running gear and steering
2.16. Suspension bracket and steering check
2.17. Driveshaft check
2.18. Check of an exhaust system
2.19. Check and adjustment of a pedal of coupling
2.20. Check of level of oil in a manual transmission
2.21. Check of level of oil in a transfer case
2.22. Check of level of oil and картередифференциала (or in a reducer of the back bridge)
2.23. Shift of wheels
2.24. Check of brakes
2.25. Check of fuel system
2.26. Check of the thermostat of the air filter
2.27. Drive belts - check, adjustment and replacement
2.28. Check of seat belts
2.29. Replacement of the air filter and filter of ventilation of a case
2.30. Replacement of the fuel filter
2.31. Replacement of the filter of the ezhektsionny valve of system of a dookisleniye exhaust gases
2.32. Replacement of the filter of a tank with an absorber
2.33. Check of fastening of the case of a butterfly valve
2.34. Check and adjustment of turns of idling (engines with fuel injection)
2.35. Oil replacement in a transfer case
2.36. Oil replacement in a manual transmission
2.37. Oil replacement in a reducer back (or forward) the bridge
2.38. Replacement of transmission liquid! in automatic transmission
2.39. Greasing replacement in naves of forward wheels and check of bearings (only for rear-wheel cars)
2.40. Replacement of cooling liquid
2.41. Check and replacement of a zolotnik of ventilation of a case
2.42. Replacement of spark plugs
2.43. High-voltage wires - check and replacement
2.44. A cover of the distributor and a rotor begunok - check and replacement.
2.45. Check and installation of the moment of ignition.
2.46. Oxygen sensor
3. Четырехцилиндровыв engines
4. VS engines
5. All engines
6. Systems of cooling, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and furnish elements
17. Electric equipment system


2.13. Replacement of oil and oil filter

1. Replacement of oil is the simplest operation which can be executed independently.
2. Replacement of the filter is expedient for combining with oil replacement.
3. Before the beginning of works prepare all necessary tools and materials.
4. Establish the car on a hole or a platform.
5. Wipe a drain stopper of the pallet.
6. Warm up the engine.
7. Oil changes on completely heated-up engine.
8. Substitute under a drain stopper the pallet and release a stopper.
9. Turn out a stopper, the last some turns rotate a stopper slowly (photo).
10. Merge oil in the substituted pallet.
11. After running off of oil wipe a stopper pure rags (photo).
12. Wipe the pallet about a drain opening and wrap a stopper. Densely tighten a stopper with the set moment.
13. Rearrange the pallet under the oil filter.

13.9а the Drain stopper on the V6 engine

13.9б the Drain stopper on the 4-cylinder engine

14. By means of a special key release the oil filter (photo)
13,14 Oil filter on the V6 engine (at the left) and 4-cylinder (on the right) to release
15. Turn out the filter hands.
16. Be convinced that the type and the sizes of the new filter completely coincide with type and the sizes of the fulfilled.
17. Wipe pure rags a place of a prileganiye of the filter on the block of cylinders. Remove laying.
18. Slightly oil for the engine rubber laying of the new filter (photo).
13.18 Before a wraparound of the filter grease filter laying by fresh oil for the engine.
19. Wrap the filter and tighten the filter by hand.
20. Clean the tool and lower the car.
21. Fill in oil of the necessary brand through a stopper oil - a jellied mouth on a cover of a head of cylinders.
22. At first fill in about 0,8 l of oil then wait some minutes that all oil flew down in the pallet and shchupy check oil level.
23. Continue to add oil in the small portions, before achievement of a mark "L". Start the engine that oil filled all lubricant channels.
24. Stop the engine and immediately check oil leaks, if necessary tighten a stopper or the filter.
25. Check level and if necessary add oil.
26. In we say lies several trips after oil change especially watch closely a leak and check oil level.

14.22 Order of adjustment of valves 1. To a forward part of the engine

13.11 The metal particles which have stuck to a magnetic stopper

«previous page
2.12. Check and adjustment of a pedal of a brake
following page»
2.14. Check and adjustment of gaps of valves