Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Car maintenance
2.1. Introduction
2.2. Maintenance terms
2.3. An order of performance of adjustments - general comments
2.4. Check of level of liquids
2.5. Check of level of liquid in automatic transmission
2.6. Check of level of liquid of the power steering
2.7. Check of tires (through each 400 kilometers or weekly)
2.8. Care of the battery
2.9. Care of cooling system
2.10. Check of brushes of screen wipers
2.11. Check of a condition of the hoses located in a motor compartment.
2.12. Check and adjustment of a pedal of a brake
2.13. Replacement of oil and oil filter
2.14. Check and adjustment of gaps of valves
2.15. Greasing of a running gear and steering
2.16. Suspension bracket and steering check
2.17. Driveshaft check
2.18. Check of an exhaust system
2.19. Check and adjustment of a pedal of coupling
2.20. Check of level of oil in a manual transmission
2.21. Check of level of oil in a transfer case
2.22. Check of level of oil and картередифференциала (or in a reducer of the back bridge)
2.23. Shift of wheels
2.24. Check of brakes
2.25. Check of fuel system
2.26. Check of the thermostat of the air filter
2.27. Drive belts - check, adjustment and replacement
2.28. Check of seat belts
2.29. Replacement of the air filter and filter of ventilation of a case
2.30. Replacement of the fuel filter
2.31. Replacement of the filter of the ezhektsionny valve of system of a dookisleniye exhaust gases
2.32. Replacement of the filter of a tank with an absorber
2.33. Check of fastening of the case of a butterfly valve
2.34. Check and adjustment of turns of idling (engines with fuel injection)
2.35. Oil replacement in a transfer case
2.36. Oil replacement in a manual transmission
2.37. Oil replacement in a reducer back (or forward) the bridge
2.38. Replacement of transmission liquid! in automatic transmission
2.39. Greasing replacement in naves of forward wheels and check of bearings (only for rear-wheel cars)
2.40. Replacement of cooling liquid
2.41. Check and replacement of a zolotnik of ventilation of a case
2.42. Replacement of spark plugs
2.43. High-voltage wires - check and replacement
2.44. A cover of the distributor and a rotor begunok - check and replacement.
2.45. Check and installation of the moment of ignition.
2.46. Oxygen sensor
3. Четырехцилиндровыв engines
4. VS engines
5. All engines
6. Systems of cooling, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and furnish elements
17. Electric equipment system
 








2-15-smazka-khodovojj-chasti-i-rulevogo-upravleniya.html

2.15. Greasing of a running gear and steering

1. Accessories to greasing are shown on a photo. 15.1 Accessories to greasing
2. To greasing of a running gear and a steering it is applied universal lithium greasings  to Greasing spherical support of levers of a forward suspension bracket, tips of steering drafts, forward and reverse kardanny gear (on cars With a wheel formula 4x4) are subject.
3. The place of greasing of the top support is in the top part of the case of a support (photo), for greasing it is necessary to remove a wheel. Access to a butterdish of the bottom support is provided through an opening in the lever (photo). An opening for greasing tips of steering drafts turn out a cap (photo). On kardanny transfer hinges and shlitsevy sliding connection (photo) are greased.
4. Lift the car and establish on supports.
5. Turn out caps and screw butterdishes (on a part of cars).
6. Squeeze out a little greasing from a syringe and wipe absolutely.

15.3а the Carving opening under a butterdish for greasing of the top support is muffled by a stopper
15.3а the Carving opening under a butterdish for greasing of the top support is muffled by a stopper


15.3в an opening Cap under a butterdish in a draft tip
15.3в an opening Cap under a butterdish in a draft tip


7. Grease with a syringe all connections. Spherical support шприцуйте until then while greasing will not fill rubber covers (it is felt on pressing). If greasing it vykho-is put from a butterdish, tighten a butterdish or turn out and check purity of the valve of a butterdish.
8. Remove the greasing remains.
15.3г an opening Cap under a butterdish on the kardanny hinge
15.3г  an opening Cap under a butterdish on the kardanny hinge


15.3б the Opening in the lever for greasing of the bottom support (on and/m early releases)
15.3б the Opening in the lever for greasing of the bottom support (on and/m early releases)


15. Зг Butterdish of shlitsevy connection
15. Зг Butterdish of shlitsevy connection


9. Grease a cable and levers of the hand brake.
10. Lower the car.
11. Grease rubbing details of locks of a cowl and a back door, grease the terminations of cables.
12. Grease loops of doors with several drops of oil for the engine.
13.  Cylindrical  switches  of locks  of doors are greased with aerosol graphite greasing.

«previous page
2.14. Check and adjustment of gaps of valves
following page»
2.16. Suspension bracket and steering check