Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Car maintenance
2.1. Introduction
2.2. Maintenance terms
2.3. An order of performance of adjustments - general comments
2.4. Check of level of liquids
2.5. Check of level of liquid in automatic transmission
2.6. Check of level of liquid of the power steering
2.7. Check of tires (through each 400 kilometers or weekly)
2.8. Care of the battery
2.9. Care of cooling system
2.10. Check of brushes of screen wipers
2.11. Check of a condition of the hoses located in a motor compartment.
2.12. Check and adjustment of a pedal of a brake
2.13. Replacement of oil and oil filter
2.14. Check and adjustment of gaps of valves
2.15. Greasing of a running gear and steering
2.16. Suspension bracket and steering check
2.17. Driveshaft check
2.18. Check of an exhaust system
2.19. Check and adjustment of a pedal of coupling
2.20. Check of level of oil in a manual transmission
2.21. Check of level of oil in a transfer case
2.22. Check of level of oil and картередифференциала (or in a reducer of the back bridge)
2.23. Shift of wheels
2.24. Check of brakes
2.25. Check of fuel system
2.26. Check of the thermostat of the air filter
2.27. Drive belts - check, adjustment and replacement
2.28. Check of seat belts
2.29. Replacement of the air filter and filter of ventilation of a case
2.30. Replacement of the fuel filter
2.31. Replacement of the filter of the ezhektsionny valve of system of a dookisleniye exhaust gases
2.32. Replacement of the filter of a tank with an absorber
2.33. Check of fastening of the case of a butterfly valve
2.34. Check and adjustment of turns of idling (engines with fuel injection)
2.35. Oil replacement in a transfer case
2.36. Oil replacement in a manual transmission
2.37. Oil replacement in a reducer back (or forward) the bridge
2.38. Replacement of transmission liquid! in automatic transmission
2.39. Greasing replacement in naves of forward wheels and check of bearings (only for rear-wheel cars)
2.40. Replacement of cooling liquid
2.41. Check and replacement of a zolotnik of ventilation of a case
2.42. Replacement of spark plugs
2.43. High-voltage wires - check and replacement
2.44. A cover of the distributor and a rotor begunok - check and replacement.
2.45. Check and installation of the moment of ignition.
2.46. Oxygen sensor
3. Четырехцилиндровыв engines
4. VS engines
5. All engines
6. Systems of cooling, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and furnish elements
17. Electric equipment system
 








2-4-proverka-urovnya-zhidkostejj.html

2.4. Check of level of liquids

1. Before check establish the car on an equal horizontal platform.
Oil in the engine
2. Level of oil is checked shchupy (photo).
3. Level of oil is checked before driving on the car, or about 15 minutes later after an engine stop.
4.4г the Arrangement of marks on oil щупе1. Normal уровень2. A3 type. B4 type. On V65 engines. On 4-cylinder engines
4.4г the Arrangement of marks on oil щупе
1. Normal level
2. Type A
3. Type B
4. On V6 engines
5. On 4-cylinder engines


4.4б On 4-cylinder engines with 8 candles щуп it is located in the left back part of the engine
4.4б On 4-cylinder engines with 8 candles щуп it is located in the left back part of the engine


4.4в On V6 engines щуп it is located in a back part of the engine near the amplifier of brakes
4.4в On V6 engines щуп it is located in a back part of the engine near the amplifier of brakes


4. Get control щуп from a tube and wipe it pure rags or a paper napkin. Insert pure щуп against the stop into a branch pipe and again get. Level should be between marks L (at least) and N (at most).
5. Support oil level only between the specified marks.
6. Oil add through a mouth on a cover of a head of cylinders (photo).
4.6 The mouth stopper on the V6 engine is on the right cover of a head of cylinders
4.6 The mouth stopper on the V6 engine is on the right cover of a head of cylinders


4.8 Broad tank of system of cooling
4.8 Broad tank of system of cooling


7. Attentively check an oil condition on щупе. Emulsion pollution can be caused by cracks in the block or in a head of cylinders, and also laying destruction therefore it is necessary to check an engine condition.
Cooling liquid
8. All cars considered in this management, have system of cooling of an elevated pressure with return of liquid to a broad tank (photo).
9. On the cold engine level should be between marks "MIN' and "MOVE" on a broad tank On the heated-up engine level can be near a mark "MOVE". If it is necessary to restore level, wait engine cooling, uncover a broad tank and add liquid of necessary structure antifreeze/water (it is recommended 50/50).
10. After a trip again check level.
4.14 Tank стеклоомыватвля
4.14 Tank стеклоомыватвля


11. Need of a frequent dolivaniye indicates violation of tightness of system. Check existence on a radiator, hoses and demountable connections of traces of podtekaniye in the form of spots, or uvlazhneniye. If obvious signs of a leak it is not revealed, it is recommended to check a radiator stopper, and tightness of all system an opressovka method (pressure giving) at car repair shop.
12. A stopper of a mouth of a radiator to turn on only on the cooled-down engine.
13. At detection of traces of pollution wash out system and replace liquid.
Liquid in a washer tank.
14. The tank of a stekloomyvatel is in a motor compartment from the driver (photo).
15. In a temperate climate in a tank of a stekloomyvatel pure water approximately on 2/3 tanks is filled in. In a frigid climate liquid of special structure is filled in.
16. To prevent a zapotevaniye in cold weather, before inclusion of a smyvatel warm up glass from a defreezing nozzle of a heater.
Check of level of electrolit
17. New cars are completed with batteries with the transparent case in which level of electrolit is visible through the case (photo). If necessary add the distilled water.
Restoration of level of liquid in a hydraulic actuator of brakes and couplings
18. The main cylinder of brakes and its tank are mounted on the vacuum amplifier in a motor compartment. The main cylinder of coupling is mounted on a partition of a motor compartment.
19. Level of liquid should be between marks of min and max in tanks (photo).
20. In a tank of brakes add only liquid of recommended brand, mixing of liquids of various brands is not allowed.

Attention!
Brake liquid has harmful effects on eyes and destroys a paint and varnish covering therefore filling in liquid be careful. Brake liquid absorbs moisture from air therefore it is forbidden to fill in liquid which was a long time in open container in brakes. Excess of moisture leads to dangerous loss of efficiency of braking.

21. At detection of pollution it is necessary to merge and replace liquid.
22. After level restoration a tank stopper densely wrap.

4.17 Marks between which there should be an electrolit level
4.17 Marks between which there should be an electrolit level


4.19а liquid Level should be in a tank of brakes about the top label
4.19а liquid Level should be in a tank of brakes about the top label


23. During normal work of system liquid level gradually goes down in process of wear of brake slips. If frequent addition of brake liquid is required, in a hydraulic actuator of system there is a leak which it is necessary to eliminate immediately.
24. If level liquid in tanks is lower than norm, it is necessary to remove air from a hydraulic actuator.


«previous page
2.3. An order of performance of adjustments - general comments
following page»
2.5. Check of level of liquid in automatic transmission