Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Car maintenance
2.1. Introduction
2.2. Maintenance terms
2.3. An order of performance of adjustments - general comments
2.4. Check of level of liquids
2.5. Check of level of liquid in automatic transmission
2.6. Check of level of liquid of the power steering
2.7. Check of tires (through each 400 kilometers or weekly)
2.8. Care of the battery
2.9. Care of cooling system
2.10. Check of brushes of screen wipers
2.11. Check of a condition of the hoses located in a motor compartment.
2.12. Check and adjustment of a pedal of a brake
2.13. Replacement of oil and oil filter
2.14. Check and adjustment of gaps of valves
2.15. Greasing of a running gear and steering
2.16. Suspension bracket and steering check
2.17. Driveshaft check
2.18. Check of an exhaust system
2.19. Check and adjustment of a pedal of coupling
2.20. Check of level of oil in a manual transmission
2.21. Check of level of oil in a transfer case
2.22. Check of level of oil and картередифференциала (or in a reducer of the back bridge)
2.23. Shift of wheels
2.24. Check of brakes
2.25. Check of fuel system
2.26. Check of the thermostat of the air filter
2.27. Drive belts - check, adjustment and replacement
2.28. Check of seat belts
2.29. Replacement of the air filter and filter of ventilation of a case
2.30. Replacement of the fuel filter
2.31. Replacement of the filter of the ezhektsionny valve of system of a dookisleniye exhaust gases
2.32. Replacement of the filter of a tank with an absorber
2.33. Check of fastening of the case of a butterfly valve
2.34. Check and adjustment of turns of idling (engines with fuel injection)
2.35. Oil replacement in a transfer case
2.36. Oil replacement in a manual transmission
2.37. Oil replacement in a reducer back (or forward) the bridge
2.38. Replacement of transmission liquid! in automatic transmission
2.39. Greasing replacement in naves of forward wheels and check of bearings (only for rear-wheel cars)
2.40. Replacement of cooling liquid
2.41. Check and replacement of a zolotnik of ventilation of a case
2.42. Replacement of spark plugs
2.43. High-voltage wires - check and replacement
2.44. A cover of the distributor and a rotor begunok - check and replacement.
2.45. Check and installation of the moment of ignition.
2.46. Oxygen sensor
3. Четырехцилиндровыв engines
4. VS engines
5. All engines
6. Systems of cooling, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and furnish elements
17. Electric equipment system
 







peri szalunki systemowe, oraz w i

2-45-proverka-i-ustanovka-momenta-zazhiganiya.html

2.45. Check and installation of the moment of ignition.

Attention!
On engines after 1990 the moment of ignition is regulated by automatically processor block.

45.4 A mark in a pulley and a scale for ignition installation on 4-cylinder engines
45.4 A mark in a pulley and a scale for ignition installation on 4-cylinder engines


45.2 A mark in a pulley and a scale for installation for zhiganiye on 4-cylinder engines
45.2 A mark in a pulley and a scale for installation for zhiganiye on 4-cylinder engines


1. At check of a corner of installation of ignition be guided by data in the plate strengthened from the vnutry party of a cowl.
2. On 4-cylinder engines the moment of ignition is checked on combination of a mark in a pulley the crankshaft with division of the scale mounted over a pulley (photo) the Label 0 there corresponds VMT.
3. Designate a mark in a pulley light paint
4. On the V6 engine the ignition moment the scale is checked on combination of the motionless index from division on a scale put on a pulley of an uspokoitel (photo).
5. Check idling turns, if necessary adjust. Connect a stroboscope according to the instruction of the manufacturer.
6. Warm up the engine, stop and disconnect devices which are specified in the podkapotny plate for this engine
7. Attach a stroboscope according to the instruction from a gotovitel.
8. Start the engine, 2-3 times press a pedal of gas and transfer to an idling mode.
9. Direct stroboscope light on a crankshaft pulley the Shined label should be opposite to the corresponding division of a scale.

45.11 Installation of ignition 1. Increase in a corner of an advancing 2. Corner reduction
45.11 Installation of ignition 1. Increase in a corner of an advancing 2. Corner reduction


10. In need of adjustment release adjusting bolts of the distributor.
11. For installation of ignition turn the distributor case before combination of a label with the necessary division of a scale (photo). Tighten bolts and again check ignition installation.
12. Disconnect a stroboscope and check idling turns, if necessary adjust.
13. If at a trip ringing knocks at car movement on lifting are listened or at dispersals, again attach a stroboscope and reduce an advancing corner on 1-2 °.

«previous page
2.44. A cover of the distributor and a rotor begunok - check and replacement.
following page»
2.46. Oxygen sensor