Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Car maintenance
2.1. Introduction
2.2. Maintenance terms
2.3. An order of performance of adjustments - general comments
2.4. Check of level of liquids
2.5. Check of level of liquid in automatic transmission
2.6. Check of level of liquid of the power steering
2.7. Check of tires (through each 400 kilometers or weekly)
2.8. Care of the battery
2.9. Care of cooling system
2.10. Check of brushes of screen wipers
2.11. Check of a condition of the hoses located in a motor compartment.
2.12. Check and adjustment of a pedal of a brake
2.13. Replacement of oil and oil filter
2.14. Check and adjustment of gaps of valves
2.15. Greasing of a running gear and steering
2.16. Suspension bracket and steering check
2.17. Driveshaft check
2.18. Check of an exhaust system
2.19. Check and adjustment of a pedal of coupling
2.20. Check of level of oil in a manual transmission
2.21. Check of level of oil in a transfer case
2.22. Check of level of oil and картередифференциала (or in a reducer of the back bridge)
2.23. Shift of wheels
2.24. Check of brakes
2.25. Check of fuel system
2.26. Check of the thermostat of the air filter
2.27. Drive belts - check, adjustment and replacement
2.28. Check of seat belts
2.29. Replacement of the air filter and filter of ventilation of a case
2.30. Replacement of the fuel filter
2.31. Replacement of the filter of the ezhektsionny valve of system of a dookisleniye exhaust gases
2.32. Replacement of the filter of a tank with an absorber
2.33. Check of fastening of the case of a butterfly valve
2.34. Check and adjustment of turns of idling (engines with fuel injection)
2.35. Oil replacement in a transfer case
2.36. Oil replacement in a manual transmission
2.37. Oil replacement in a reducer back (or forward) the bridge
2.38. Replacement of transmission liquid! in automatic transmission
2.39. Greasing replacement in naves of forward wheels and check of bearings (only for rear-wheel cars)
2.40. Replacement of cooling liquid
2.41. Check and replacement of a zolotnik of ventilation of a case
2.42. Replacement of spark plugs
2.43. High-voltage wires - check and replacement
2.44. A cover of the distributor and a rotor begunok - check and replacement.
2.45. Check and installation of the moment of ignition.
2.46. Oxygen sensor
3. Четырехцилиндровыв engines
4. VS engines
5. All engines
6. Systems of cooling, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and furnish elements
17. Electric equipment system
 








2-34-proverka-i-regulirovka-oborotov-kholostogo-khoda-dvigateli-s-vpryskom-topliva.html

2.34. Check and adjustment of turns of idling (engines with fuel injection)

1. Independent check and adjustment of turns of idling is allowed on engines after 1990 g equipped with system of direct injection. Connect a tachometer according to the instruction of the manufacturer. Before adjustment disconnect all units of fuel system providing automatic adjustment of idling (Hl. 4 and 6).
а). On V6 engines disconnect the socket of perepuskny air AAS-of the valve (photo). On K24 engines disconnect the socket from the sensor of an angle of rotation of a butterfly valve.
б). Check ignition installation (see below),
в). Rotating the screw, establish turns of idling (photo).
г). Attach sockets and finish turns to 2000 rpm, sustain the engine in such mode within several minutes.
д). If the engine still unstably idles, check and adjust quality of a mix (WITH) in car-care center service.

34.1а the Socket of perepuskny AAS-of the valve on V6 engines (it is disconnected before idling adjustment) 1. Socket
34.1а the Socket of perepuskny AAS-of the valve on V6 engines (it is disconnected before idling adjustment) 1. Socket


34.16 The socket of the sensor of an angle of rotation of a butterfly valve on K24 engines (it is disconnected before idling adjustment) 1. Socket
34.16 The socket of the sensor of an angle of rotation of a butterfly valve on K24 engines (it is disconnected before idling adjustment)
1. Socket


34.1в the Screw of adjustment of idling on V61 engines. Увеличить2. Уменьшить3. Adjusting screw
34.1в the Screw of adjustment of idling on V6 engines
1. To increase
2. To reduce
3. Adjusting screw


34.1г the Screw of adjustment of idling on K241 engines. Rubber колпачок2. Perepuskna valve
34.1г the Screw of adjustment of idling on K24 engines
1. Rubber cap 
2. Perepuskna valve


36.3 Otvorachivaniye of a drain stopper in a check point case
36.3 Otvorachivaniye of a drain stopper in a check point case



«previous page
2.33. Check of fastening of the case of a butterfly valve
following page»
2.35. Oil replacement in a transfer case