Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Car maintenance
2.1. Introduction
2.2. Maintenance terms
2.3. An order of performance of adjustments - general comments
2.4. Check of level of liquids
2.5. Check of level of liquid in automatic transmission
2.6. Check of level of liquid of the power steering
2.7. Check of tires (through each 400 kilometers or weekly)
2.8. Care of the battery
2.9. Care of cooling system
2.10. Check of brushes of screen wipers
2.11. Check of a condition of the hoses located in a motor compartment.
2.12. Check and adjustment of a pedal of a brake
2.13. Replacement of oil and oil filter
2.14. Check and adjustment of gaps of valves
2.15. Greasing of a running gear and steering
2.16. Suspension bracket and steering check
2.17. Driveshaft check
2.18. Check of an exhaust system
2.19. Check and adjustment of a pedal of coupling
2.20. Check of level of oil in a manual transmission
2.21. Check of level of oil in a transfer case
2.22. Check of level of oil and картередифференциала (or in a reducer of the back bridge)
2.23. Shift of wheels
2.24. Check of brakes
2.25. Check of fuel system
2.26. Check of the thermostat of the air filter
2.27. Drive belts - check, adjustment and replacement
2.28. Check of seat belts
2.29. Replacement of the air filter and filter of ventilation of a case
2.30. Replacement of the fuel filter
2.31. Replacement of the filter of the ezhektsionny valve of system of a dookisleniye exhaust gases
2.32. Replacement of the filter of a tank with an absorber
2.33. Check of fastening of the case of a butterfly valve
2.34. Check and adjustment of turns of idling (engines with fuel injection)
2.35. Oil replacement in a transfer case
2.36. Oil replacement in a manual transmission
2.37. Oil replacement in a reducer back (or forward) the bridge
2.38. Replacement of transmission liquid! in automatic transmission
2.39. Greasing replacement in naves of forward wheels and check of bearings (only for rear-wheel cars)
2.40. Replacement of cooling liquid
2.41. Check and replacement of a zolotnik of ventilation of a case
2.42. Replacement of spark plugs
2.43. High-voltage wires - check and replacement
2.44. A cover of the distributor and a rotor begunok - check and replacement.
2.45. Check and installation of the moment of ignition.
2.46. Oxygen sensor
3. Четырехцилиндровыв engines
4. VS engines
5. All engines
6. Systems of cooling, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and furnish elements
17. Electric equipment system
 







ֳ .

2-39-zamena-smazki-v-stupicakh-perednikh-koles-i-proverka.html

2.39. Greasing replacement in naves of forward wheels and check of bearings (only for rear-wheel cars)

1. Lyufta in bearings of a nave check each time when lifting a forward part of the car.
2. Turn a wheel and check freedom of rotation люфты.
3. If at a wheel kachaniye in the vertical plane it is felt люфт, it is necessary to check bearings to replace greasing in a nave
4. Remove a wheel
5. Remove a support, take aside and fix.
6. Vypressuyte cap of a nave (photo).

39.6 Removal of a cap of a nave
39.6 Removal of a cap of a nave


39.7 Nave and bearing forward колеса1. Сальник2. Internal подшипник3. Ступица4. External подшипник5. Шайба6. Кольцо7. Шплинт8. Колпачок9. Adjusting гайка10. Disk тормоза11. Brake board
39.7 Nave and bearing of a forward wheel
1. Epiploon
2. Internal bearing
3. Nave
4. External bearing
5. Washer
6. Ring
7. Шплинт
8. Cap
9. Adjusting nut
10. Brake disk 
11. Brake board

7. Rasshplintuyte  cap  of an adjusting  nut (photo).
8. Unscrew a nut and remove a washer.
9. Submit a nave on itself and push back, get the external bearing.
10. Remove a nave from a pin of a rotary fist.
11. Hook a screw-driver and get an epiploon (photo). Pay attention to epiploon orientation in a nave.
12. Get the internal bearing.
13. Wash out bearings and a nave from greasing, clear a pin.
14. Check a condition of rollers and external holders of bearings in naves. In case of damages on their external holders it is necessary выпрессовать (it is carried out at car repair shop) and to replace bearings.
15. Put in bearings refractory greasing, having carefully filled space in a holder of rollers (photo).
16. Grease places of landing of bearings on a pin and boring under an epiploon.

39.11 Extraction of an epiploon of a nave
39.11 Extraction of an epiploon of a nave


17. Put greasing for holders of bearings, having covered edges of holders and having created a fillet for greasing preservation in bearings.
18. Insert the greased internal bearing and put greasing on its external part.
19. Press a new epiploon.
20. Establish a nave and dress the external bearing.
21. Dress a washer and tighten a nut with the moment of 3 N of m.
22. Turn a nave in both directions.
23. Believe the moment of an inhaling and again turn a nave in both directions. Check the moment of resistance a provorachivaniya which should remain equal 3 N of m.
24. Wrap a nut on 45 °.
25. Dress a koronchaty cap and зашплинтуйте. If necessary tighten a nut clockwise that шплинт passed in grooves of a cap and in a pin opening.
26. Bend шплинт so that it did not touch a nave cap.

39.15 Greasing of bearings of a nave
39.15 Greasing of bearings of a nave


40.4 The ventilating valve of system of cooling on V6 engines
40.4 The ventilating valve of system of cooling on V6 engines


27. Napressuyte a nave cap, having tracked safety of a sealing ring.
28. Dress a wheel, tighten nuts and having shaken, check люфт in bearings. Lower the car.

«previous page
2.38. Replacement of transmission liquid! in automatic transmission
following page»
2.40. Replacement of cooling liquid