Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Car maintenance
3. Четырехцилиндровыв engines
3.1. General information
3.2. Types of the repair work which is carried out without dismantle of the engine from the car
3.3. An order of installation of the piston of the 1st cylinder in VMT of a step of compression.
3.4. A cover of a head of cylinders - removal and installation
3.5. The roller with yokes - removal and installation
3.6. The roller with yokes - dismantling and assembly
3.7. A cam-shaft - removal and installation
3.8. A cam-shaft, support and yokes - check
3.9. Springs of valves and maslosjemny caps - replacement
3.10. A soaking-up collector - removal and installation
3.11. A final collector - removal and installation
3.12. A head of cylinders - removal
3.13. A head of cylinders - installation
3.14. The oil pump - removal and installation
3.15. The oil pump - check
3.16. A crankshaft pulley - removal and installation
3.17. A forward epiploon of the crankshaft - replacement
3.18. A forward cover - removal and installation
3.19. A chain and asterisks - removal and installation
3.20. The oil pallet - removal and installation
3.21. A flywheel (a leading disk of the hydrotransformer) - removal and installation
3.22. A back epiploon - replacement
3.23. Engine support - replacement
4. VS engines
5. All engines
6. Systems of cooling, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and furnish elements
17. Electric equipment system
 








3-14-maslyanyjj-nasos-snyatie-i-ustanovka.html

3.14. The oil pump - removal and installation

1. Establish the piston 1 - го the cylinder in VMT of a step of compression.
2. Uncover the distributor of ignition and обо4 mean situation a begunka concerning the distributor case.
3. Lift a forward part of the car and establish on supports.
4. Remove engine mudguards.
5. Merge oil from the engine.
6. On cars with a formula 4x4 establish a support under a forward reducer.
7. Unscrew bolts and remove the pump assembled with shaft.
8. The order of dismantling of the pump is described in below.
9. Be convinced that the piston of the 1st cylinder is in VMT of a step of compression.
10. Fill the pump with oil, combine a label навалу) the pump with a lubricant opening under a leading gear wheel (photo).
11. Establish laying and the pump.
12. Tighten bolts and check shaft coca orientation. If necessary repeat operation устаноааЩ
13. Fill in oil. Check ignition installation

14.10 At pump installation the label on a shaft should be opposite to a lubricant opening of the pump
14.10 At pump installation the label on a shaft should be opposite to a lubricant opening of the pump


15.1 Details oil насоса1, Val2,4-Prokladka3. Корпус5. Gear wheels (conducting and conducted) 6. Крышка7. Заглушка8. Шайба9. Пружина10. Клапан11. Reduktsionny valve
15.1 Details of the oil pump
1, Shaft
2,4-Laying
3. Case
5. Gear wheels (conducting and conducted)
6. Cover
7. Cap
8. Washer
9. Spring
10. Valve
11. Reduktsionny valve


«previous page
3.13. A head of cylinders - installation
following page»
3.15. The oil pump - check