Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Car maintenance
3. Четырехцилиндровыв engines
3.1. General information
3.2. Types of the repair work which is carried out without dismantle of the engine from the car
3.3. An order of installation of the piston of the 1st cylinder in VMT of a step of compression.
3.4. A cover of a head of cylinders - removal and installation
3.5. The roller with yokes - removal and installation
3.6. The roller with yokes - dismantling and assembly
3.7. A cam-shaft - removal and installation
3.8. A cam-shaft, support and yokes - check
3.9. Springs of valves and maslosjemny caps - replacement
3.10. A soaking-up collector - removal and installation
3.11. A final collector - removal and installation
3.12. A head of cylinders - removal
3.13. A head of cylinders - installation
3.14. The oil pump - removal and installation
3.15. The oil pump - check
3.16. A crankshaft pulley - removal and installation
3.17. A forward epiploon of the crankshaft - replacement
3.18. A forward cover - removal and installation
3.19. A chain and asterisks - removal and installation
3.20. The oil pallet - removal and installation
3.21. A flywheel (a leading disk of the hydrotransformer) - removal and installation
3.22. A back epiploon - replacement
3.23. Engine support - replacement
4. VS engines
5. All engines
6. Systems of cooling, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and furnish elements
17. Electric equipment system
 








3-19-cep-i-zvezdochki-snyatie-i-ustanovka.html

3.19. A chain and asterisks - removal and installation

Removal
1. Remove a forward cover.
2. Unscrew bolts of a natyazhitel, a boot and an uspokoitel, take these details (photo).
3. Reject a bolt and remove a cam-shaft asterisk (see above).
4. Remove a chain.
5. Remove a maslootrazhatel, a gear wheel of a drive of the oil pump, and a leading asterisk (photo).
6. Check a condition of teeths of asterisks, having compared profiles of teeths on both parties. At detection of a kryuchkovatost of teeths of an asterisk replace.
7. The chain changes together with worn-out asterisks, or through each 48000 km. Also it is necessary to replace a chain at detection of signs of wear of rollers.
8. Establish an asterisk on a cam-shaft and check it axial люфт which should not exceed 0,2 mm.

19.5 Removal of a leading asterisk
19.5 Removal of a leading asterisk


19.2 Drive chain распредвала1. Натяжитель2. Uspokoitel левый3. Uspokoitel правый4. Маслоотражатель5. Gear wheel of a drive oil насоса6. Leader звездочка7. Chain
19.2 Chain of a drive of a cam-shaft
1. Natyazhitel
2. Uspokoitel left
3. Uspokoitel right
4. Maslootrazhatel
5. Gear wheel of a drive of the oil pump
6. Leading asterisk
7. Chain


9. Check a condition of a natyazhitel and uspokoitel, if necessary replace.
Installation
10. Turn a cam-shaft so that valves of the 1st cylinder were closed. The crankshaft establish so that the piston 1 - го the cylinder was in VMT.
11. Establish uspokoitel.
12. Establish a maslootrazhatel, a gear wheel of a drive of the oil pump, and a leading asterisk on a crankshaft sock. Be convinced that adjusting labels on a leading asterisk are turned forward (photo).
13. Before chain installation turn of the crankshaft is not allowed.

19.12 At assembly the shponka should be turned up, and a label on an asterisk - forward
19.12 At assembly the shponka should be turned up, and a label on an asterisk - forward


19.14а On the Z24i engine the chain link with distinctive coloring should be combined with a label on a cam-shaft asterisk, and the adjusting pin of a cam-shaft should come into an opening at number 2
19.14а On the Z24i engine the chain link with distinctive coloring should be combined with a label on a cam-shaft asterisk, and the adjusting pin of a cam-shaft should come into an opening at number 2


19.14г On all engines a chain link with distinctive coloring should be it is combined with a label on a leading asterisk
19.14г On all engines a chain link with distinctive coloring should be it is combined with a label on a leading asterisk


14. Dress a chain on a cam-shaft asterisk, then get on a leading asterisk. Tighten a bolt of an asterisk of a cam-shaft. At assembly keep in mind the following:
а). Shponka of the crankshaft should be turned up.
б). Chain links with distinctive coloring should be combined with labels on asterisks, and settle down on the right, if to look in front (photo).
в). The adjusting pin of a cam-shaft should come into an opening in an asterisk at number of 2 (photos).
15. Establish a natyazhitel, adjust the provision of the left uspokoitel so that the gap between the case of a natyazhitel and a boot was absent (photo).
16. Establish a forward cover.

«previous page
3.18. A forward cover - removal and installation
following page»
3.20. The oil pallet - removal and installation