Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Car maintenance
3. Четырехцилиндровыв engines
3.1. General information
3.2. Types of the repair work which is carried out without dismantle of the engine from the car
3.3. An order of installation of the piston of the 1st cylinder in VMT of a step of compression.
3.4. A cover of a head of cylinders - removal and installation
3.5. The roller with yokes - removal and installation
3.6. The roller with yokes - dismantling and assembly
3.7. A cam-shaft - removal and installation
3.8. A cam-shaft, support and yokes - check
3.9. Springs of valves and maslosjemny caps - replacement
3.10. A soaking-up collector - removal and installation
3.11. A final collector - removal and installation
3.12. A head of cylinders - removal
3.13. A head of cylinders - installation
3.14. The oil pump - removal and installation
3.15. The oil pump - check
3.16. A crankshaft pulley - removal and installation
3.17. A forward epiploon of the crankshaft - replacement
3.18. A forward cover - removal and installation
3.19. A chain and asterisks - removal and installation
3.20. The oil pallet - removal and installation
3.21. A flywheel (a leading disk of the hydrotransformer) - removal and installation
3.22. A back epiploon - replacement
3.23. Engine support - replacement
4. VS engines
5. All engines
6. Systems of cooling, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and furnish elements
17. Electric equipment system
 








3-6-valik-s-koromyslami-razborka-i-sborka.html

3.6. The roller with yokes - dismantling and assembly

1. Remove all bolts except for two bolts on both ends.
2. Holding the roller, carefully get 2 extreme bolts, let's be straightened by springs.
3. Remove yokes and designate so that at assembly to establish on former places.
4. Replace rollers if on them there are wear signs.

6.5а Orientation of rollers of yokes at assembly (Z24 engine) 1. Пазы2. Кернения3. Roller final клапанов4. Roller inlet клапанов5. To a forward part of the engine
6.5а Orientation of rollers of yokes at assembly (Z24 engine)
1. Grooves
2. Kerneniya
3. Roller of final valves
4. Roller of inlet valves
5. To a forward part of the engine


6.5б Adjusting labels on arms of rollers and on a head of cylinders 1. To a forward part of the engine 2. Labels on arms 3. Labels on a head of cylinders
6.5б Adjusting labels on arms of rollers and on a head of cylinders 1. To a forward part of the engine 2. Labels on arms 3. Labels on a head of cylinders


6.5в Orientation of brackets at assembly of rollers with yokes (the engine K24J 1,2. Cut 3. From inlet valves 4. From final valves
6.5в Orientation of brackets at assembly of rollers with yokes (the engine K24J 1,2. Cut 3. From inlet valves 4. From final valves





7.6 Otvorachivaniye of a bolt of an asterisk of a cam-shaft
7.6 Otvorachivaniye of a bolt of an asterisk of a cam-shaft


7.8 Chain fixing by a wedge
7.8 Chain fixing by a wedge


7.12 Before installation grease cam-shaft necks
7.12 Before installation grease cam-shaft necks


5. Establish the roller in a forward arm, combine openings and insert bolts. On the roller of inlet valves grooves are provided. At assembly establish rollers so that kerneniye at their end faces were turned up. Arms establish being guided on labels (photo).
6. Dress yokes, compress a spring and establish back arms, insert bolts. Establish rollers and a cover upside-down.

«previous page
3.5. The roller with yokes - removal and installation
following page»
3.7. A cam-shaft - removal and installation