Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Car maintenance
3. Четырехцилиндровыв engines
3.1. General information
3.2. Types of the repair work which is carried out without dismantle of the engine from the car
3.3. An order of installation of the piston of the 1st cylinder in VMT of a step of compression.
3.4. A cover of a head of cylinders - removal and installation
3.5. The roller with yokes - removal and installation
3.6. The roller with yokes - dismantling and assembly
3.7. A cam-shaft - removal and installation
3.8. A cam-shaft, support and yokes - check
3.9. Springs of valves and maslosjemny caps - replacement
3.10. A soaking-up collector - removal and installation
3.11. A final collector - removal and installation
3.12. A head of cylinders - removal
3.13. A head of cylinders - installation
3.14. The oil pump - removal and installation
3.15. The oil pump - check
3.16. A crankshaft pulley - removal and installation
3.17. A forward epiploon of the crankshaft - replacement
3.18. A forward cover - removal and installation
3.19. A chain and asterisks - removal and installation
3.20. The oil pallet - removal and installation
3.21. A flywheel (a leading disk of the hydrotransformer) - removal and installation
3.22. A back epiploon - replacement
3.23. Engine support - replacement
4. VS engines
5. All engines
6. Systems of cooling, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and furnish elements
17. Electric equipment system
 






3-20-maslyanyjj-poddon-snyatie-i-ustanovka.html

3.20. The oil pallet - removal and installation

1. Merge oil.
2. Lift a forward part of the car and establish on supports.
3. Remove engine mudguards.
4. On cars with a formula 4x9 remove a stretcher.
5. On cars with a formula 4x4 remove a forward reducer, will hang out the engine, having weakened support. Fix support wooden whetstones.
6. Unscrew bolts and remove the oil pallet. At removal do not damage the demountable planes of the block of cylinders and the pallet.

19.14в On the K24 engine the link with silvery coloring should be combined with a label on a cam-shaft asterisk


19.15а Take aside an uspokoitel.


19.15б the Gap between the case of a natyazhitel and a boot after assembly should be absent
1. Natyazhitel
2. After assembly


21.2 Flywheel removal


7. Carefully clear the demountable planes of the block of cylinders and the pallet of the consolidation remains. Wash out the condensed planes solvent of varnishes or acetone. Be convinced of purity of carving openings in the block of cylinders.
8. Check existence on the demountable plane of the pallet of deformations, especially about openings under bolts. If necessary отрихтуйте the demountable plane a hammer, having laid on a wooden board.
9. Put on the pallet plane RTV hermetic with a thin layer and lay laying.
10. Establish the pallet and evenly in a cross order tighten bolts with set, the moment. Through 30 mines (after a hermetic skhvatyvaniye) fill in oil, start the engine and be convinced of lack of leaks.

«previous page
3.19. A chain and asterisks - removal and installation
following page»
3.21. A flywheel (a leading disk of the hydrotransformer) - removal and installation