Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Car maintenance
3. Четырехцилиндровыв engines
4. VS engines
4.1. General information
4.2. Types of the repair work which is carried out without dismantle of the engine from the car
4.3. An order of installation of the piston of the 1st cylinder in VMT of a step of compression.
4.4. Covers of heads of cylinders – removed and installation
4.5. The roller with yokes - removal and installation
4.6. Hydropushers - removal and installation
4.7. A soaking-up collector - removal and installation
4.8. A final collector - removal and installation
4.9. A pulley - an uspokoitel - removal and
4.10. A gear belt - removal and installation
4.11. A forward epiploon of the crankshaft - replacement
4.12. A cam-shaft epiploon - replacement
4.13. Heads of cylinders - removal and installation
4.14. A cam-shaft - removal and installation
4.15. Details of the klapanny mechanism - check
4.16. The oil pallet - removal and installation
4.17. The oil pump - removal, check and installation
4.18. A back epiploon - replacement
4.19. A flywheel (a leading disk of the hydrotransformer) -
4.20. Engine support - replacement
5. All engines
6. Systems of cooling, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and furnish elements
17. Electric equipment system
 








4-13-golovki-cilindrov-snyatie-i-ustanovka.html

4.13. Heads of cylinders - removal and installation

1. Execute a decompression of fuel system, disconnect the battery from weight and спейте liquid.

12.4 Labels й and L conflicts on asterisks two fishing)
12.4 Labels й and L conflicts on asterisks two fishing)


12.5б an epiploon Press fitting (the same adaptation, as for a crankshaft epiploon is used)
12.5б an epiploon Press fitting (the same  adaptation, as for a crankshaft epiploon is used)


13.3 Bolts of fastening of a back cover of a gear belt
13.3 Bolts of fastening of a back cover of a gear belt


2. Will remove a gear belt, the case of a zaslonka, a vsasye a howling collector, asterisks of cam-shafts.
3. Will unscrew bolts and take a back cover of a belt (photo).
13.7а Order of an otpuskaniye of bolts of a head цилиндров1. To a forward part
13.7а Order of an otpuskaniye of bolts of a head of cylinders
1. To a forward part


13.8 A bolt in the lower part of a head of cylinders
13.8 A bolt in the lower part of a head of cylinders


13.14а Orientation of washers of a head цилиндров1. Towards a head
13.14а Orientation of washers of a head of cylinders
1. Towards a head


Removal of the left head
4. Remove the compressor and take aside, without disconnecting the highway.
5. Remove the distributor, the generator, an arm of the generator and a final collector.
6. Remove details of the klapanny mechanism.
7. Evenly and gradually unscrew bolts of a head of cylinders and store them in an initial order (photo).
8. Unscrew a small bolt in the lower part of a head (photo) and carefully remove a head.
Right head
9. Remove the pump of the hydraulic booster and take aside.

13.7б One of ways of storage of bolts on a pattern of laying of a head of cylinders (it is possible to remove from new laying). Designate a forward part, and also the right and left parties of a head of cylinders
13.7б One of ways of storage of bolts on a pattern of laying of a head of cylinders (it is possible to remove from new laying). Designate a forward part, and also the right and left parties of a head of cylinders


13.13 Soriyentiruyte laying on pins on the block of cylinders
13.13 Soriyentiruyte laying on pins on the block of cylinders


13.14б Order of a tightening of bolts of a head. Bolts 4,5,12 and 13 are longer остальных1. Right головка2. Left head
13.14б Order of a tightening of bolts of a head. Bolts 4,5,12 and 13 are longer than the others
1. Right head                      
2. Left head


14.3 Bolts of a face cover.
14.3 Bolts of a face cover.


14.4б... unscrew the central bolt
14.4б... unscrew the central bolt


10. Remove a final collector, details of the klapanny mechanism and unscrew bolts of a head of cylinders (see above).
11. Unscrew a small bolt in the lower part of a head and carefully remove a head of cylinders
Installation
12. Carefully clear the demountable planes of the block and a head, small roughnesses polish, banish and clear all carving openings.
13. Lay on the block new laying (photo).
14. Wrap by hand bolts of a head of cylinders on former places. The flat part of washers of bolts should be turned towards a head of cylinders (photo).
15. Tighten bolts in 5 stages with the set moment in the specified sequence (photo).
16. Other operations are carried out upside-down. Replace oil and the filter.

«previous page
4.12. A cam-shaft epiploon - replacement
following page»
4.14. A cam-shaft - removal and installation