Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Car maintenance
3. Четырехцилиндровыв engines
4. VS engines
4.1. General information
4.2. Types of the repair work which is carried out without dismantle of the engine from the car
4.3. An order of installation of the piston of the 1st cylinder in VMT of a step of compression.
4.4. Covers of heads of cylinders – removed and installation
4.5. The roller with yokes - removal and installation
4.6. Hydropushers - removal and installation
4.7. A soaking-up collector - removal and installation
4.8. A final collector - removal and installation
4.9. A pulley - an uspokoitel - removal and
4.10. A gear belt - removal and installation
4.11. A forward epiploon of the crankshaft - replacement
4.12. A cam-shaft epiploon - replacement
4.13. Heads of cylinders - removal and installation
4.14. A cam-shaft - removal and installation
4.15. Details of the klapanny mechanism - check
4.16. The oil pallet - removal and installation
4.17. The oil pump - removal, check and installation
4.18. A back epiploon - replacement
4.19. A flywheel (a leading disk of the hydrotransformer) -
4.20. Engine support - replacement
5. All engines
6. Systems of cooling, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and furnish elements
17. Electric equipment system
 








4-4-kryshki-golovok-cilindrov-snyatoe-i-ustanovka.html

4.4. Covers of heads of cylinders – removed and installation

1. Execute a decompression of fuel system.

3.4а Mark O in a pulley and index
3.4а Mark O in a pulley and index


3.4б When division About on a pulley will coincide with the index... 1. Scale of installation of ignition
3.4б When division About on a pulley will coincide with the index...
1. Scale of installation of ignition


3.5... and the begunok indicates the put label, the piston of the 1st cylinder is in VMT of a step of compression 1. Begunok
3.5... and the begunok indicates the put label, the piston of the 1st cylinder is in VMT of a step of compression 1. Begunok


2. Disconnect the battery from weight.
Right cover
3. Disconnect a hose of ventilyatsiya of a case (photo)
4. Designate and disconnect from wire candles, take them aside.
5. Disconnect from a cover hoses and wires.
6. Unscrew screws of a cover and remove washers.
4.3 Hoses and wires, which should be disconnected to remove the right cover of a head of cylinders
4.3 Hoses and wires, which should be disconnected to remove the right cover of a head of cylinders


4.8 A hose and a wire, which should be disconnected to remove the left cover of a head of cylinders
4.8 A hose and a wire, which should be disconnected to remove the left cover of a head of cylinders


5.3 Lay bolts of rollers in cash desk as it should be to them installations
5.3 Lay bolts of rollers in cash desk as it should be to them installations


7. Uncover, having carefully opened consolidation.
Left cover
8. Disconnect from a cover a hose сапуна (Photo).
9. Designate and disconnect from wire candles.
10. Get from wire arms.
11. Unscrew 9 screws and uncover.
Installation
12. Clear a cover of the consolidation remains, put in a cover flute hermetic and lay laying. After a skhvatyvaniye of hermetic establish a cover and wrap screws.
13. Evenly tighten screws in 3-4 receptions.
14. Other procedures are carried out upside-down.
15. Warm up the engine and be convinced of lack of a leak

«previous page
4.3. An order of installation of the piston of the 1st cylinder in VMT of a step of compression.
following page»
4.5. The roller with yokes - removal and installation