Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Car maintenance
3. Четырехцилиндровыв engines
4. VS engines
4.1. General information
4.2. Types of the repair work which is carried out without dismantle of the engine from the car
4.3. An order of installation of the piston of the 1st cylinder in VMT of a step of compression.
4.4. Covers of heads of cylinders – removed and installation
4.5. The roller with yokes - removal and installation
4.6. Hydropushers - removal and installation
4.7. A soaking-up collector - removal and installation
4.8. A final collector - removal and installation
4.9. A pulley - an uspokoitel - removal and
4.10. A gear belt - removal and installation
4.11. A forward epiploon of the crankshaft - replacement
4.12. A cam-shaft epiploon - replacement
4.13. Heads of cylinders - removal and installation
4.14. A cam-shaft - removal and installation
4.15. Details of the klapanny mechanism - check
4.16. The oil pallet - removal and installation
4.17. The oil pump - removal, check and installation
4.18. A back epiploon - replacement
4.19. A flywheel (a leading disk of the hydrotransformer) -
4.20. Engine support - replacement
5. All engines
6. Systems of cooling, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and furnish elements
17. Electric equipment system
 








4-16-maslyanyjj-poddon-snyatie-i-ustanovka.html

4.16. The oil pallet - removal and installation

1. Disconnect the battery from weight.

15.86 Measurement of diameter of an opening in a yoke.
15.86 Measurement of diameter of an opening in a yoke.


15.6б... and openings under a pusher in the case I
15.6б... and openings under a pusher in the case I


15.8а Diameter of the roller is measured in the yoke location
15.8а Diameter of the roller is measured in the yoke location


2. Lift a forward part of the car and establish on supports.
3. Remove a guard of a case and merge oil.
4. Remove a starter.
5. Remove brackets of fastening of a bell-shaped case to the engine.
6. Remove the pendular lever.
7. On cars 4x2 remove arms of the stabilizer of stability.
8. On cars 4x2 remove a stretcher.
9. On cars 4x4 remove an arm передня a reducer.

16.17а Put hermetic in places of a prileganiye of the holder of a back epiploon and the oil pump
16.17а Put hermetic in places of a prileganiye of the holder of a back epiploon and the oil pump  


16.17б Places of drawing of hermetic on laying поддона1. Laying
16.17б Places of drawing of hermetic on pallet laying
1. Laying


17.3а Bolts of the oil pump
17.3а Bolts of the oil pump


10. Remove transmission support.
11. Disconnect from collectors exhaust pipes.
12. Will hang out the power unit on a waist or establish under it a jack.
13. Unscrew bolts of fastening of support of the engine to a frame.
14. Raise the engine a little, being careful.
15. Unscrew bolts and remove the pallet.
16. Carefully clear the demountable planes of the block of cylinders and the pallet of the consolidation remains. Banish and clear carving openings in the block of cylinders.
17. Put on the demountable planes hermetic (photo).
18. Establish laying on the pallet, establish the pallet and evenly in a cross order tighten bolts with the set moment (photo).

«previous page
4.15. Details of the klapanny mechanism - check
following page»
4.17. The oil pump - removal, check and installation